MedElevator Войти в исследования
← Поиск публикаций

DOI 10.5152/j.aott.2021.21332

Медицинская библиотека · Acta orthopaedica et traumatologica turcica · 2022

Patient-specific three-dimensional printing spine model for surgical planning in AO spine type-C fracture posterior long-segment fixation.

Öztürk Anıl Murat, Süer Onur, Govsa Figen, Özer Mehmet Asım, Akçalı Ömer

СтатьяРандомизированное исследованиеПеревод в очереди

Аннотация

OBJECTIVE

The aim of this study was to compare duration of surgery, intraoperative fluoroscopy exposure, blood loss and the accuracy of pedicular screw placement between 3D model-assisted surgery and conventional surgery for AO spinal C-type injuries.

METHODS

In this study 32 patients who were admitted with thoracolumbar AO spinal C-type injuries were included. These patients were divided randomly into two groups of 16 where one group was operated on using conventional surgery and the other group was operated on using 3D model-assisted surgery. During surgery, instrumentation time, amount of blood loss and intraoperative fluoroscopy exposure were recorded. Moreover, the status of the screws in the pedicles was assessed as described by Learch and Wiesner's and regional sagittal angles (RSA) were measured preop and postoperatively.

RESULTS

It was found that there was a statistically significant difference in instrumentation time, blood loss and intraoperative fluoroscopy exposure in the 3D model-assisted surgery group (61.9 ± 4.7 min, 268.4 ± 42.7 ml, 16.3 ± 1.9 times) compared to the conventional surgery group (75.5 ± 11.0 min, 347.8 ± 52.2 mL, 19.7 ± 2.4 times) (t=4.5325, P < 0.0001 and t=4.7109, P < 0.0001 and t=4.4937, P < 0.0001, respectively) Although the screw misplacement rate of the conventional surgery group was higher than that of the 3D model-assisted surgery group, the only statistically significant difference was in the medial axial encroachment (t=5.101 P=0.02) . There was no severe misplacement of pedicle screws in either group. There were no statistically significant differences between postoperative RSA angles and were in both groups restored significantly.

CONCLUSION

The results of this study have shown us that the 3D model helps surgeons see patients' pathoanatomy and determine rod lengths, pedicle screw angles and lengths preoperatively and peroparatively, which in turn shortens operative time, reduces blood loss and fluoroscopy exposure.

LEVEL OF EVIDENCE: Level I, Therapeutic Study.

Для цитирования: Öztürk Anıl Murat, Süer Onur, Govsa Figen, Özer Mehmet Asım, Akçalı Ömer. Patient-specific three-dimensional printing spine model for surgical planning in AO spine type-C fracture posterior long-segment fixation.. Acta orthopaedica et traumatologica turcica. 2022. DOI: 10.5152/j.aott.2021.21332.

Предметные рубрики MeSH

Подготовка и перевод публикации
Обработка статьи · этапы, ошибки и управление
Загрузка состояния…

История · было → стало

Состояние обновляется каждые 5 секунд, пока блок открыт. Процент показывается только там, где известен объём работы. Пауза останавливает продолжение этапа; текущий запрос к источнику может завершиться.

Тип публикации указан по данным источника. Уровень доказательности автоматически не присваивается.