PloS one · 2026
Advanced preclinical testing of a design-optimized ceramic bearing for a cervical total disc replacement.
СтатьяНазвание и аннотация: Перевод в очереди
Обработка статьи · этапы, ошибки и управление
Загрузка состояния…
Ошибки и ограничения
История · было → стало
Состояние обновляется каждые 5 секунд, пока блок открыт. Процент показывается только там, где известен объём работы. Пауза останавливает продолжение этапа; текущий запрос к источнику может завершиться.
Kölle Lucia, Pryce Gregory, Beadling Andrew R, Bryant Michael, Hall Richard M, Ferguson Stephen J, Helgason Benedikt
Аннотация
OBJECTIVE: Arthroplasty in the cervical spine is performed using Total Disc Replacement (TDR) implants. This study investigates the safety and tribology of a design-optimized ceramic TDR bearing.
METHODS: Samples of an optimized bearing geometry were manufactured from the bioceramic BIOLOX®delta (CeramTec GmbH, Germany) and tested in a six degree of freedom universal joint simulator in diluted calf serum at body temperature. The investigated load and motion profiles simulated movements of daily living; three pure rotations under static load and three rotations coupled under sinusoidal load as well as adverse events (three subluxation test conditions).
RESULTS: Dynamic coefficients of friction during flexion/extension and lateral bending were µ = 0.16 ± 0.011 and µ = 0.16 ± 0.070, respectively. Friction factors during flexion/extension and lateral bending were f = 0.14 ± 0.0092 and f = 0.13 ± 0.063, whereas the friction factor in axial rotation was f = 0.033 ± 0.0028 and for three coupled rotations under sinusoidal load, it was f = 0.13 ± 0.028. The design demonstrated a sufficient resistance against subluxation, with subluxation forces more than 3.5-fold the 20N that are typically required as acceptance criteria in FDA safety and effectiveness data.
CONCLUSION: Friction values were found to be comparable to or higher than those typically reported for ceramic-on-ceramic hip replacements. Furthermore, the results indicated that the optimized bearing design is sufficiently resistant to subluxation. Significance: Test protocols to investigate safety and tribology of cervical TDRs are proposed and their results are reported for a design-optimized ceramic TDR bearing.
METHODS: Samples of an optimized bearing geometry were manufactured from the bioceramic BIOLOX®delta (CeramTec GmbH, Germany) and tested in a six degree of freedom universal joint simulator in diluted calf serum at body temperature. The investigated load and motion profiles simulated movements of daily living; three pure rotations under static load and three rotations coupled under sinusoidal load as well as adverse events (three subluxation test conditions).
RESULTS: Dynamic coefficients of friction during flexion/extension and lateral bending were µ = 0.16 ± 0.011 and µ = 0.16 ± 0.070, respectively. Friction factors during flexion/extension and lateral bending were f = 0.14 ± 0.0092 and f = 0.13 ± 0.063, whereas the friction factor in axial rotation was f = 0.033 ± 0.0028 and for three coupled rotations under sinusoidal load, it was f = 0.13 ± 0.028. The design demonstrated a sufficient resistance against subluxation, with subluxation forces more than 3.5-fold the 20N that are typically required as acceptance criteria in FDA safety and effectiveness data.
CONCLUSION: Friction values were found to be comparable to or higher than those typically reported for ceramic-on-ceramic hip replacements. Furthermore, the results indicated that the optimized bearing design is sufficiently resistant to subluxation. Significance: Test protocols to investigate safety and tribology of cervical TDRs are proposed and their results are reported for a design-optimized ceramic TDR bearing.