American journal of dentistry · 2019
Incorporation of ZnCl2 into an etch-and-rinse adhesive system on flexural strength, degree of conversion and bond durability to caries-affected dentin.
СтатьяНазвание и аннотация: Перевод в очереди
Обработка статьи · этапы, ошибки и управление
Загрузка состояния…
Ошибки и ограничения
История · было → стало
Состояние обновляется каждые 5 секунд, пока блок открыт. Процент показывается только там, где известен объём работы. Пауза останавливает продолжение этапа; текущий запрос к источнику может завершиться.
Oliveira Cérida Ar, Campos Rosa Mp, Macedo Julia Pc, Silva Anderson R, Máximo Leandro Nc, Silva Tânia M, França Fabiana Mg, Turssi Cecília P, Basting Roberta T, Gonçalves Sergio Eduardo de P, Amaral Flavia Lb
Аннотация
PURPOSE: To evaluate the effect of a zinc chloride (ZnCl2) solution (2% wt), incorporated into a two-step etch-and-rinse adhesive system (AS), on microtensile bond strength (µTBS) to caries-affected dentin (CAD).
METHODS: First, the degree of conversion (DC) of the AS with and without the ZnCl2 solution was evaluated by Fourier transform infrared spectroscopy (FTIR). Second, beam-shaped samples (7 mm × 2 mm × 1 mm) were prepared with the AS containing the ZnCl2 solution to perform flexural strength (FS) tests. For µTBS testing purposes, CAD surfaces were etched with phosphoric acid and randomly divided into three groups (n=10) : ZnCl2- AS with ZnCl2; NT (no treatment)- AS without ZnCl2; and CHX - pretreatment with 2% chlorhexidine solution. AS (Adper Single Bond 2) was applied according to the manufacturer's instructions, and resin composite restorations were built up. After 24 hours, the resin-dentin blocks were sectioned into specimens (0.8 mm2), and then subjected to micro;TBS testing immediately following, or after 6 or 12 months of water storage (WS). The adhesive interface was evaluated by scanning electron microscope. Both µTBS and FS tests were performed using a universal testing machine ( 0.5 mm/minute). FS and DC data were submitted to the Student t-test, and µTBS data were subjected to two-way ANOVA and Tukey's test (α= 0.05).
RESULTS: DC was not affected by ZnCl2 incorporation into AS (P= 0.2527). Higher FS values were obtained in the group with ZnCl2 added to AS. Regarding µTBS, the mean of the NT group was statistically higher than that of the ZnCl2 or the CHX groups (P< 0.001(, regardless of WS, but the latter groups did not differ from each other. µTBS at 24 hours was statistically superior to that of 6 and 12 months of WS (P< 0.001).
METHODS: First, the degree of conversion (DC) of the AS with and without the ZnCl2 solution was evaluated by Fourier transform infrared spectroscopy (FTIR). Second, beam-shaped samples (7 mm × 2 mm × 1 mm) were prepared with the AS containing the ZnCl2 solution to perform flexural strength (FS) tests. For µTBS testing purposes, CAD surfaces were etched with phosphoric acid and randomly divided into three groups (n=10) : ZnCl2- AS with ZnCl2; NT (no treatment)- AS without ZnCl2; and CHX - pretreatment with 2% chlorhexidine solution. AS (Adper Single Bond 2) was applied according to the manufacturer's instructions, and resin composite restorations were built up. After 24 hours, the resin-dentin blocks were sectioned into specimens (0.8 mm2), and then subjected to micro;TBS testing immediately following, or after 6 or 12 months of water storage (WS). The adhesive interface was evaluated by scanning electron microscope. Both µTBS and FS tests were performed using a universal testing machine ( 0.5 mm/minute). FS and DC data were submitted to the Student t-test, and µTBS data were subjected to two-way ANOVA and Tukey's test (α= 0.05).
RESULTS: DC was not affected by ZnCl2 incorporation into AS (P= 0.2527). Higher FS values were obtained in the group with ZnCl2 added to AS. Regarding µTBS, the mean of the NT group was statistically higher than that of the ZnCl2 or the CHX groups (P< 0.001(, regardless of WS, but the latter groups did not differ from each other. µTBS at 24 hours was statistically superior to that of 6 and 12 months of WS (P< 0.001).