Гибридные композитные соединения с оксидами металлов: всеобъемлющий обзор синтеза и многофункциональных видов применения.

Introduction

Conducting polymers (CPs) have been extensively researched over the past few decades owing to their great potential to replace their conventional inorganic counterparts. Toward the end of 1970, many scientists believed that CPs were elusive and insoluble. Numerous significant CPs have been constantly studied since Hideki Shirakawa, Alan MacDiarmid, and Alan Heeger discovered polyacetylene in 1970. They investigated that when SN x (sulphur nitride) metal is doped with bromine, its electrical and optical properties are enhanced. Later, a study was conducted on polyacetylene, and it was found that polyacetylene doped with bromine has million times more electrical conductivity than pristine polyacetylene. This investigation was awarded the Nobel prize in 2000. 1–4 Organic CPs include polypyrrole, polyaniline, polythiophene 5 and polyacetylene, which are similar to inorganic semiconductor materials owing to their distinct electrical and optical properties. Conjugated CPs have a pattern of single and double bonds, bond polarization and conjugating electron-π dense bonds that enhance their electrical behavior. Throughout the 1970s, a range of CPs were developed; nevertheless, because of their low thermoplasticity and limited compatibility with the most conventional solvent processing of CPs and creation of soluble versions of these materials, they became a top precedence for research. Moreover, under normal conditions, CPs have limited conductivity and possess poor mechanical features, unlike most commercially available polymers. CP composites were developed to address these drawbacks. 6

Doping significantly increases the amount of charge carriers in CPs, which modulate and enhance the electrical properties of CPs. 7 MO x are selected for integration in CPs because of their favorable electrical properties, eco-friendliness, cost-effectiveness, easy incorporation/doping in polymer materials, biosafety and biocompatibility. 8 MO x @CP composites showed improved electrochemical properties: First, the quantity of metal oxide composites integrated on the electrode surface increased; (2) electron transport speed increased; (3) the distribution of metal oxide composites became more consistent; (4) the activity of electrocatalysis enhanced, and there was significant improvement in stability.

Previous studies have highlighted the excellent results in different fields achieved by MO x @CPs. Diverse approaches exist for the monitoring of biological analytes. Some drawbacks of the traditional analytical methods are their length, the need for preliminary preparations, the need for skilled workers, and the high cost of supplies and equipment. Thus, research in the area of biosensor design has garnered a lot of attention in order to determine biomolecules quantitatively and accurately within a short period of time. 9,10 Researchers have created biosensors with a low limit of detection (LOD), great selectivity, and sensitivity using a range of CPs. These synthetic polymers have attained a great deal of interest as a suitable sustaining framework for immobilizing biological components. MO x @CPs standout as excellent candidates for biosensors to detect biomarkers in disease diagnosis 10,11 Saddique et al. developed a Nb 2 O 5 -incorporated polythiophene biosensor for the sensing of creatinine biomarker of chronic kidney disease from saliva with a very low LOD of 34 pM and an excellent sensitivity of 4.614 μA cm −2 nM −1 . 12

Beyond sensing application, MO x @CPs have significant potential in energy storage devices i.e. in supercapacitors and batteries. Supercapacitors are widely used in automotive systems, portable electronics, and a variety of other applications. They are seen to be the best option for sophisticated energy storage systems. Because of their benefits over SCs, LIBs have been the focus of an increasing number of investigation studies. 13 When two electrodes are polarized by a neutral signal, two beds of contrasting charges arise at the boundary between the electrode and the electrolyte. The two layers are closer to one another than in traditional capacitors, having contrasting charges and being alike to an atomic gap, which results in a considerable energy gain. Because of their excessive power and energy density, SCs are therefore anticipated to lie in between Li-ion and traditional capacitors. 14 Higher efficiency, greater density of energy, and longer life cycles make SCs more required and flexible for use in electronic vehicles, portable gadgets and energy backup systems. K. P. Gautam et al. developed core shell NiO@PANI for supercapacitor applications. The NiO-polyaniline-based electrode material demonstrated an excellent specific capacitance of 623 F g −1 at a current density of 1 Ag −1 . Moreover, it shows excellent stability retaining 89.4% of its initial response over 5000 cycles GCD at a current density of 20 A g −1 . 15 J. Yesuraj et al. utilized a NiMoO 4 -PANI hybrid electrode material as a supercapacitor, which exhibited an excellent specific capacitance of 285 F g −1 and remarkable stability over the 500 cycles by retaining 92% of its initial response. 16,17

The sensible development of long-lasting, highly effective catalysts that are also cost effective and accessible is essential to electrocatalytic water splitting. Therefore, it is vital to have an effective electrocatalyst that can proficiently follow the electrolytic catalysis of the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). 18,19 MO x @CPs stand out as excellent candidates for this purpose. Alsultan et al. synthesized MnCo 2 O 4 /PPy, a chemically polymerized pyrrole, with H 2 O 2 . They found that the hybrid substance surpassed pristine materials in the OER, with an extreme potential of about 480 mV, which is similar to the benchmark for RuO 2 /C (20%). The electrocatalyst's enhanced electrical conductivity was credited with this improvement. 20

This comprehensive review discusses various synthetic strategies, advancement, properties and applications of MO x @CPs in different areas. Despite the substantial progress, most studies on MO x @CPs have been limited to specific applications, often omitting the broader multifunctionality of these materials. This comprehensive study aims to bridge this gap by offering insights from various domains, including recent innovations, challenges in biomedical applications, energy storage devices, water splitting and photocatalysis, highlighting the core concepts governing their performance in each field.

Conducting polymers (CPs)

Polymers were considered to be electrical insulators before the invention of CPs such as PTh, PANI, PPy and PA, 4,21,22 as shown in Fig. 1 . The significance and attention to this unique class of organic materials have increased dramatically. Among polymeric materials, CPs are regarded as the fourth generation. For many years, this class of materials have been the focus of scientific study towards energy applications because of their unique electrical conductivity, which in certain situations reached that of metals, together with their physicochemical features, which are inherited from the conventional polymeric materials. 23,24 Common polymers are easily prepared and processable, and their electrical conductivity is comparable to that of metals and inorganic semiconductors. CPs are basically synthesized macromolecules containing highly delocalized π-conjugated backbone structures and tunable side chains ( Table 1 ). 25

Traditional polymers such as polyethene and polyvinyl chloride comprise thousands to millions of monomer units and are stiff and soluble in various solvents. Their rigidity limits their flexibility and processability. In contrast, conjugated CPs such as PTh and PA consist of fewer monomer units and their delocalized π-electrons and alternating single and double bonds confer the flexibility and enhance their unique electrical and mechanical properties. This delocalization plays a central role in establishing polarons, bipolarons and solitons, which are unique features for their transition from insulators to semiconductors and conductors. 2

CPs offer remarkable benefits over conventional materials, such as extensive and adjustable electrical conductivity, easy fabrication, high mechanical stability, low weight, affordability and simplicity of material production. They are appropriate for a range of applications due to their better electrochemical activity, greater surface area and electrical conductivity. The blending of CPs with additional metal oxides has produced functional nanocomposites that showed promise and succeeded in enhanced effectiveness across a variety of domains including energy harvesting sensors, energy storage devices 31 and biomedical systems. 32

Molecular orbital theory insights into the electrical behavior of conducting polymers

Mechanism of conduction

Conventional theory illustrates that in CPs, delocalized electrons of π bonds are responsible for electron flow and their electrical conduction behavior. Although a single bond exclusively has a sigma bond with localized electrons, a double bond possesses both a weaker π bond and localized σ bond. 33 The displacement of π bonds, which happens in the tandem interaction bridging the first and second carbon atoms and the second and third carbon atoms, allows electrons to get through. Additionally, the following pair receives the π bond bridging the third and fourth carbon atoms, as shown in Fig. 2(c) . 2

MOT addresses electrical behavior at the molecular level. 2,35 In the MOT approach, molecules are considered to be a superposition of p orbitals, and this leads to a low-energy bonding molecular orbital (π) and a high-energy antibonding molecular orbital (π*). However, the highest occupied valence band HOMO and the lowest occupied conduction band LUMO are the results of combination of bonding and antibonding molecular orbitals, respectively. The band gap is the HOMO–LUMO energy gap, also known as “forbidden energy gap”, “energy gap” or “fundamental energy gap”. 36 In CPs, bonding and antibonding molecular orbitals create energy band with filled (π-electronic band) HOMO and vacant (π*-band) LUMO. Conjugation in the polymeric structure is increased with the increase in the number of monomer units and results in the development of wide-ranging energy states with a narrow band gap. However, electrons exhibit unrestricted motion throughout backbone starts to take place. Generally, CPs have a band gap that places them between the insulator (>3 eV) and the semiconductor within the range (0–3 eV). There are few parameters that control the conjugated polymer band gap. (1) A shift in bond length, (2) resonance energy, (3) structural planarity, (4) consequences of substituents, (5) conjugation length, and (6) donor and acceptor connections. 37 PA has a π–π* band gap of 1.5 eV and a conductivity within the range of 10 3 –1.7 × 10 5 S cm −1 . PTh has a π–π* band gap of 2 eV and a conductivity in the range of 10–10 3 S cm −1 , whereas PPy has a band gap of 3.1 eV and a conductivity within the range of 10 2 –7.5 × 10 3 S cm −1 in the same way PANI has a band gap larger than that mentioned for CPs of about 3.5 eV and a conductivity of 30–200 S cm −1 , as shown in Fig. 2 . 2,38

Other advanced computational approaches such as DFT provide an understanding of charge transfer in CPs. Band creation and delocalization are described by MOT, which offers conceptual basis for charge transfer in CPs. DFT enhances this image by adding electron correlation effects, charge localization and accurate band gap prediction. The Kohn–Sham approach in DFT facilitates the calculation of charge transfer properties, band structure and excitonic interactions in CPs. Hybrid functionals such as B3LYP and HSE06 are utilized to precisely access the band gaps and charge mobility, offering an extensive understanding of the electronic transport dynamic. 39

Marcus Theory and Electron transfer mechanism describe the electron transfer as a function of reorganization energy and donor–acceptor coupling. The charge transfer k_ET depends on parameters such as Gibbs free energy change Δ G 0 , electron coupling H_AB and nuclear reorganization energies ( λ ). Polymers with well-ordered backbone planarity and efficient π-π stacking interactions present reduced reorganization energies and, consequently, improved charge mobility and conductivity. 40

Polaron and bipolaron transport in CPs comprises quasiparticles that emerge from structural relaxations of the polymer backbone following charge injection. The formation and stabilization of polarons and bipolarons act as crucial in charge transfer processes, improving charge flow and electrical conductivity in doped polymers. The existence of counterions incorporated during doping enhances the stability of these charge carriers, reducing coulombic interactions and improving charge carrier movement. 39,41 Modern theoretical models such as DFT, Marcus theory, and polaron/bipolaron offer insights into charge transport CPs ( Table 2 ). By combining these theories, researchers can develop advanced next-generation CPs with enhanced electrical characteristics for applications in flexible electronic systems, biosensors and energy storage devices.

Properties of metal oxides

Metal oxides are a broad, versatile and attractive class of compounds due to their unique properties from metal to semiconductor and insulator. Semiconductor MO x with narrow bandgaps have significantly grasped the place in a wide range of applications in sensors, catalysts, lithium ion electrode materials, energy storage devices and electrical devices. 46 Co 3 O 4 , Al 2 O 3 , CuO, In 2 O 3 , TiO 2 , SnO 2 , ZnO, SnO, WO 3 , Fe 2 O 3 , and Cu 2 O,CeO 2 (ref. 47 ) are commonly utilized in various applications ( Fig. 3 ) because they offer excellent mechanical and chemical stability, thermal strength, and high surface area-to-volume ratios. 48

CuO has attracted more attention in different applications than Cu 2 O because of its monoclinic structure in which four oxygen atoms were bonded in a rectangular parallelogram and offer structural diversity. SnO and SnO 2 exhibit different structures, significantly rutile and tetragonal, and due to structural diversity, they have grasped a place in different applications. ZnO hexagonal wurtzite structures with intrinsic imperfections make it suitable for sensing applications. An In 2 O 3 rhombohedral structure makes it a suitable candidate for good electrical properties. The unique structural features of Al 2 O 3 are significantly used as the active phase in the field of catalysis. With these unique properties, MO x stand as excellent candidates for integration into CPs. 46,49

Doping of CPs

In doping, donor/acceptor groups are introduced into the polymer matrix. By adding or removing electrons from the CP backbone, dopant molecules are introduced, allowing for the manipulation of CP conductivity. Conjugated polymer's backbone needs to be doped with an ion or small molecule (oxidation and reduction) to enhance their properties. Charge carrier length, polymeric length and conjugation length are the parameters usually determining the doping process. 25,43 Four doping methods are briefly explained.

Redox p-doping

In this method, CPs are treated with Lewis acid such as chlorine and iodine which act as electron acceptors. This process involves the dopant to extract electrons from the HOMO of CPs. The electron is moved to the LUMO of dopant species, generating a hole in the polymer structure. As a result, the flow of electrons increases throughout the polymer chain to fill this hole. The overall process leads to electron mobility throughout the polymer and enhances the electrical conductivity of polymers. The conductivity of PA increased by p-type doping trans -[CH( i ) 0.20 ] x and became 1.6 × 10 2 S cm −1 . 50,51

Redox n-doping

CPs undergo reduction through Lewis base electron-donating species such as sodium and lithium. In this process, electrons are removed from the LUMO of doping materials and shifted to the HOMO of polymers, thereby increasing the electronic concentration in the polymer backbone, which is neutralized by dopant species counter-ions. The conductivity of PA increased by N-type dopant cis -[Li 0.30 ( CH )] x up to 2.0 × 10 2 S cm −1 . The electrical conductivity is enhanced due to increase in the density of free charge carriers as a result of N-type doping. This doping optimized the polymeric chain and enhanced the interchain transport through an improved π–π stacking interaction, which validates the enhancement in conductivity. 51

Electrochemical-p,n doping

This method of infusing the doping material is done by utilizing cathodic reduction or anodic oxidation via the electrolyte solution, which is a potential source of charge stabilization throughout the polymeric chain. However, the polymer backbone functions as an electron sink or an electron carrier to accomplish this procedure. The conductivity of undoped PPy is 8.77 × 10 −9 S cm −1 , but the conductivity of the PPy/NiO dopant increased up to 4.08 × 10 −7 S cm −1 , which is 2-fold higher than that of pristine PPy. The incorporation of dopant NiO significantly increased the electrical conductivity of PPy due to the synergetic interaction between the dopant and the CP matrix. 16,45,51

Photo-induced doping

In this method, doping is carried out by high-energy radiations that transition the electrons from the valence band of low energy to the conduction band of high energy. 36,45 Charge defects are created in the polymer configuration owing to the doping process. These electrostatic flaws such as holes and electrons can serve as charge carriers. In the first step, the formation of radicals, anions/cations, i.e. polarons, is governed by the loss or gain of an electron from the uppermost part of the valence band or the lowest point of the conduction band. It is energetically more favorable to remove/add electrons from polarons than the other locations in the polymer backbone; as a result, there is a development of bipolarons, which is a more advantageous process than the formation of two polarons. Electrical conduction occurs in bipolarons owing to positive/negative charge's delocalization. The formation of charge imperfections in PTh is depicted in Fig. 4 . Due to bipolaron bands' overlap, at high p-doping levels, the lower and higher bipolaron configurations corresponding to the occupied and unoccupied bands become energetically accessible. This opens up as a newly available valence band for electron migration, which may eventually result in a conduction mechanism that resembles a traditional metallic one. 36

Synthesis of hybrid conducting polymer composites

Various methods are used to synthesize HCP composites. The most advanced and effective techniques for developing composites of CPs and a MO x hybrid are briefly explained here. Through differential electrostatic interactions, these operations probably lead to the integration of nanounits into the primary chain of the CPs, depending on the specific MO x and the structure of the CPs. 45

HCPs are synthesized by the following strategies.

(1) Template-assisted polymerization

(i) Chemical polymerization

(ii) Electrochemical polymerization

(2) Sol–gel method

Template-assisted polymerization

The CPs created by a template-assisted polymerization technique are highly regulated, effective and easy to synthesize. In this technique, CPs develop in predetermined forms and shapes assisted by the template. 53

Hard templates need the CPs to be physically molded into desired shapes and rely on CPs' self-assembling activity. In the hard template approach, nanostructures are physically grown using physical templates that serve as molds or scaffolds that offer nanoscale, precise colloidal structures. The benefit of the hard template method is that the subsequent stages can employ either chemical or electrochemical polymerization. In order to synthesize a chemical template, the rigid template is immersed in a solution having an oxidizing agent, dopant, and monomer, which causes the monomer to polymerize, whether on the surface or throughout the pores or channels. The parameters of the template, monomer concentration, the type of oxidant, reaction duration, and temperature all affect the properties of the chemically produced CPs. 32

CPs can be produced using template-directed electrochemical synthesis that uses a metal layer serving as an electrode. Charge transport during the polymerization process, the extent and time span of applied potential, and the quantity of monomers and dopants can all have an impact on the characteristics of CPs in addition to chemical considerations. 54 The most commonly employed colloidal nanoparticles are polymer microspheres or MO x nanoparticles. The dimensions and ultimate shape of CPs are mostly governed by the colloidal nanoparticles' dimensions. This approach has multiple benefits including uniform size distribution, ease of synthesis, and large-scale acquisition. Use consistent octahedral Cu 2 O crystals (0.6–1.3 μm in rhombic length) functioning as a template in a solution containing the dopant and oxidant, for instance, to create hollow octahedral PANI. The oxidative initiator can readily remove Cu 2 O, which provides the new structure. Nevertheless, post-processing for template removal is time-consuming and could affect how hollow nanostructures turn up in the end. 32

N. Shahzad et al. synthesized PTh by the polymerization of the monomer thiophene. A uric acid hard template was employed in oxidative template-assisted polymerization ( Fig. 5 ). The template was removed by washing to free the cavities of the polymer. 55

Chemical polymerization

While synthesizing HCPs, chemical polymerization is the finest method. Chemical polymerization is considered the best technique because of its quick and simple synthetic procedure. 56 It can be further divided into addition polymerization and condensation polymerization. Because chemical polymerization is inexpensive, simple to perform, and offers a variety of pathways for the production of distinct hybrid MO x @CPs, it is widely employed. 57 In chemical polymerization, there is no need for an electrode, and it proceeds via oxidation of monomers in the presence of dopant ions. 58 A convenient route to create PANI is the chemical oxidation process, which includes blending the monomer of the relevant polymer with an oxidant alongside a suitable acid under ambient conditions to generate products. However, the formation of HCPs followed the same method. 1

PTh-g-PMA/ZnO was prepared via chemical polymerization performed in situ . Its structure, morphology and properties were studied, which showed 85% enhanced luminescence properties, which make it an excellent candidate for use in photovoltaic cells. The prepared PANI/A\ZnO hybrid composites are better candidates for anti-corrosive coating, as shown in Fig. 6 . 45

A Nb 2 O 5 -integrated PANI sensor was created by Saddique et al. to detect creatinine used in in situ oxidative polymerization of the monomer aniline with an APS solution as an oxidative initiator ensuring the controlled growth of CPs. The synthetic process used diphenyl amine crosslinked aniline on the surface of Nb 2 O 5 , 60 as shown in Fig. 7 .

Electrochemical polymerization

Electrochemical polymerization of CPs is considered non-catalytic polymerization. In electrochemical synthesis, a monomer precursor is anodically deposited on an inert metal surface, while appropriate electrolytes are analyzed. Electrochemical synthesis requires either cathodic reduction or anodic reduction of suitable electroactive functional monomers, as shown in Fig. 8 . Numerous electrochemical methods such as galvanostatic charge–discharge, potentiostatic, and CV have been used for synthesis. The principal benefit of this approach is that it allows the direct coating of a polymer film onto the metal, and the coating thickness can be smoothly tuned by adjusting the electrochemical parameters.

PA was prepared by using Luttinger's catalyst, that was a combination of complex metals [VIII] containing high molecular weight and PA was produced by this catalyst. In contrast, the Ziegler–Natta catalyst utilized water-soluble solvents for catalytic processes, such as acetonitrile or water–ethanol tetrahydrofuran (THF). Nevertheless, compared to the Zeigler-Natta catalyst, it has reduced the catalytic effectiveness, and the resulting products and catalysts have nearly identical chemical and physical properties. 1

Zhang et al. prepared a PPy/TiO 2 HCP using a gold substrate via electropolymerization and applying a steady potential of 0.85 V. The conductivity of the PPy/TiO 2 composite increased to 135 S cm −1 , a factor of ten more than that of pristine PPy (14.1 S cm −1 ). 62 The electropolymerization process has the following advantages: in most instances, the polymer is immersed directly, capable of creating thin films. The conductivity and polymer thickness are readily manipulated. 33 It is easy to use, inexpensive, and can be completed in a solitary glass vessel, and the electrochemical preparation of CPs is a highly significant technique for thin films such as sensors.

Sol–gel method

The manufacturing of HCP composites is a prospective application of flexible sol–gel technique. 63 For the first time, silicon alkoxides functioned as starting materials in the 1930s and the sol–gel process was used to create silica particles. Unlike template-assisted polymerization, the most often utilized metal alkoxides in this polymerization process are silicon alkoxide, TEOS, and TMOS ( Table 3 ). These precursors are based on silica. Condensation and hydrolysis reactions between the organic and inorganic moieties occur simultaneously to generate HCPs. Because the Si–C bonds are durable against hydrolytic degradation, it is easier to incorporate the organic group into the inorganic framework, which is the most crucial property for the formation of HCPs. This approach has several benefits, including a low reaction temperature that makes the production of HCPs easier and improves the insertion of organic constituents into the inorganic structure conversely. By using the sol–gel method, a PANI/TiO 2 hybrid was prepared. Moreover, its morphology, structure and electrochromic characteristics were examined. The PANI/TiO 2 hybrid nanocomposite was found to exhibit improved transparency and decreased crystallinity, making it a more viable option for electrochromic devices. 45

W. A. K. Mahmood et al. prepared a PANI-zirconium composite by a sol–gel technique. First, PANI was formed by dispersion polymerization of DBSA and the monomer aniline. The morphology and rod-like structure of HCPs were studied by using different techniques such as TEM, SEM and XRD. The conductive analysis of HCP composites revealed improved electrical performance, 30% more after the deposition of Zr than pure PANI. 69 The sol–gel technique for the synthesis of MO x @CPs is presented in Fig. 9 .

Photochemical polymerization

The process is less common and can be applied for the creation of some CPs. For instance, pyrrole has undergone successful polymerization into PPy using visible light irradiation, either with an appropriate electron acceptor or serving as a light sensitizer ( Table 4 ). Horseradish peroxide is presently used to initiate the polymerization of aniline in the proximity of H 2 O 2 by oxidation-radical-driven coupling reactions. It is acknowledged that aniline polymerization occurs under environmentally moderate conditions in contrast to methods involving chemicals and electrochemistry.

Several studies explored the different aspects of MO x @CPs focusing either on the synthesis strategies or on specific applications. For instance, V. V. Tran et al. developed MO x @CPs i.e. PPy/ZnO for CO 2 conversion, employed polymerization and sol–gel method to synthesize nanocomposites, lacking the in-depth analysis of their practical applications. 85 Silva et al. extensively reviewed the role of polymeric composites in biomedical applications, as this study does not delve into the multifunctional applications such as energy storage and water splitting. 86 Ghosh et al. focused on CP monohybrids for fuel cell applications emphasizing their electrocatalytic properties and synthetic strategies. However, their study lacks an in-depth exploration on multifunctional applications such as biomedicine and water splitting. 87 M. Morshed et al. used a PANI/La 2 O 3 material for supercapacitors as the PANI/La 2 O 3 electrode material exhibits a higher effective capacitance of 718 F g −1 and a specific energy of 53.8Wh/kg. The material offers remarkable power retention over 10 000 GCD cycles. 88 Z. Hao et al. used core–shell PANI/WO 3 for photochemical water splitting. Hybrid material exhibits an excellent photocurrent magnitude of 0.499 mA cm −2 , which is 2.35 times greater than the photocurrent of bare WO 3 , which is 0.212 mA cm −2 . The photoelectrochemical stability of the photoanode of hybrid PANI/WO 3 is increased up to 87% from 60%. 89 T. Marimuthu et al. used NiO-incorporated-PPy CP as a biosensor for the sensing of analyte glucose in the range of linear concentration of 0.01–0.5 mmolL −1 with a very low LOD of 0.33 μmolL −1 with an excellent sensitivity of 1094.8 μA mmol −1 L cm −2 . 32,90 Z. Zhang et al. synthesized SnO 2 @PPy as the anode for lithium ion batteries by employing sol–gel techniques. The synthesized component demonstrated superior dispersibility and electrochemical properties with a capacity of 932.6 mA h g −1 at 0.2 Ag −1 (100 cycles). This work provided an innovative method for dispersing MO x @CP composites. 91 Z. Yang et al. developed a Fe 3 O 4 -integrated PPy biosensor for the sensing of glucose with the least LOD of 0.3 μM in a wide range of concentrations of 0.5 μM-34 mM with excellent stability retaining 98.1% of its response over a time period of 20 days. 92

These studies provide comprehensive insights into MO x @CPs, but their scope remained confined to a single field. However their potential in other fields such as biomedical, electrocatalytic and water splitting technologies remained unexplored. Our review provides a holistic perspective that integrates synthetic strategies and implementation in real-world applications in biomedicine, energy and water splitting. By systematically analyzing these composites, this study highlights the synthetic advancements with multifunctional applications.

Hsissou et al. reported the synthesis and rheological characterization of a novel epoxy polymer. Their findings highlight that inorganic filler incorporation significantly increased the mechanical strength and altered the viscoelastic behavior of the polymer matrix, increasing the anticorrosive properties, 93–95 consistent with the trends observed in MO x hybrids. 96 These findings further affirm that inorganic reinforcement in polymer matrices—whether MO x or phosphate minerals—plays a pivotal role in improving mechanical, thermal, and viscoelastic properties through enhanced interfacial interactions and dispersion. The same group synthesized and characterized PGEPPP cured with MDA and reinforced with natural phosphate (PN). The PGEPPP/MDA/PN composite exhibited improved morphological uniformity, increased thermal stability, and modified rheological response 97,98 again consistent with the trends observed in our review. Furthermore, advanced functionalities, which are frequently overlooked in previous works, emphasize the MO x @CP adaptability, tunability, and developing potential ( Table 5 ). Underpinned by recent literature and state-of-the-art research, we also offer a comparative review of synthetic methodologies, comprehensive structure–property connections, and insights into the synergistic effects between inorganic and organic components.

Application in biomedical sensing

Sensor discipline is a device-centered technology, encompassing both fundamental and applied research, that is used in many different transdisciplinary domains. 114 Based on how they recognize the analytes of interest by sensing, sensors are often classified into two categories: (1) physical sensors and (2) chemical sensors. Nevertheless, present research endeavors are heading for the sensors using the combination of both physical and chemical features. 115 A chemical sensor serves as a tool for detecting and measuring specific analytes. 116 Its function is based on the idea of target species and sensor interaction. 115,117 Leveraging bio-molecules of interest, the sensors quantify molecules of biological importance. 118 Due to the overlap in sensing techniques, sensors are deemed as a component of chemical sensors. Chemical sensors using innovative methods can identify analytes with intricate chemical structures. 116 Electrochemical sensors are acclaimed for their remarkable selectivity, accuracy and precision and are classified into amperometric sensors, impedance sensors and potentiometric sensors. 119 For more quick and selective determination of analytes, electrochemical sensors are crucial. Comparing these sensors to their spectroscopic and chromatographic parallels, they are far more affordable. It can also be adjusted to fit certain uses. For potentiometric sensors, ion-responsive electrodes are pivotal for analyte detection. 120

A current signal is produced when the reactant is reduced or oxidized at a constant applied voltage. Amperometric biosensors measure this current signal. These sensors' ability to work is affected by multiple circumstances. The primary factor among them is the transmission of electrons between the catalytic molecule and the electrode/CP surface. Among other sensors, amperometric biosensors are frequently employed. The current signal is measured using an electrochemical method that is incredibly sensitive. 121,122

Potentiometric biosensor is less commonly employed in sensing. When it comes to the PPy/electrode with mounted glucose oxidase, researchers have shown its advantages over amperometric biosensors. When the sensor functioned for the detection of dopamine, it showed good detectability and selectivity. The analytical signal is thought to be the potential change rate. 123,124

Impedimetric biosensors compared to both amperometric and potentiometric sensors are infrequently employed. In order to function, impedimetric biosensors must be able to measure changes in the CP substrate's conductivity between two electrodes. The conductive nature of the component changes when the redox level or pH balance of the CP matrix changes. This sensing method takes a lot of time. 125,126 D. Minta et al. , fabricated an electrochemical sensor based on a ternary PANI/Fe 2 O 3 –SnO 2 composite on a glassy carbon electrode for the sensitive detection of dopamine and uric acid (UA). 127 The fabricated sensor demonstrated outstanding performance in detecting the target analyte, achieving an exceptionally low detection limit for UA 6.4 μM in 1.6 μM UA concentration and for DA 0.15 μM in concentration 0.076 μM at peak potential 180 mV. The sensor demonstrated excellent stability by retaining 90% of its response after use over a time period of 30 days.

In disease diagnosis – biomarker detection

Uric acid

UA is present in physiological fluids such as urine, saliva and serum. Serum and urine contain UA within the range of 300–500 μM and 1400–4400 μM, respectively. The elevated level of UA causes different diseases including gout, arthritis, high cholesterol, renal lesions and metabolic syndromes including heart attack and high blood pressure. Parkinson's disease and multiple sclerosis are caused by abnormally low levels of UA. 128 Many analytical methods such as HPLC, chemiluminescence, chromatography, and colorimetry are used for the detection of UA level. These conventional techniques, however, are typically laborious, complex, and instrument-expensive. The electrochemical methodology offers numerous advantages over traditional approaches including high sensitivity, minimal expense for upkeep, and rapid operation. 129,130

S. K. Ponnaiah et al. 130 employed a Ag–Fe 2 O 3 @PANI-modified electrode for the detection of UA. The built sensor is highly responsive to the targeted analyte UA with a sensitivity of 128.29 mAmM −1 and a remarkably low limit of detection of 102 pM. It has been proficiently accomplished to determine the UA concentration in serum and urine specimens by using the electrochemical approach. The benefits include good selectivity, a wide detection range, and quick detection. The current electrochemical sensor possesses the inherent ability to rapidly and quantitatively detect UA in real samples of patients belonging to different age groups. The sensor's selectivity was determined with different interfering analytes such as sucrose, glucose, formic acid, ascorbic acid and dopamine, which exhibited excellent selectivity by showing more response for targeted UA. On this modified electrode system, the π–π coupling connection between the analyte and the fabricated electrode active region may weaken other biological interferences while accelerating electron transport. Very low detection limits, excellent stability, and extremely high selectivity and sensitivity are all displayed by the sensor that was developed using this nanocomposite.

The Ag/Fe 2 O 3 @PANI-based UA sensor holds great promise for various applications, including evaluating the content of UA in human serum and urine samples, given its outstanding performance. This technique can be effectively used for the design of sensing devices, which offer a useful solution for medical diagnosis. 130

Creatinine

Chronic kidney disease, a progressive acute medical condition of the kidneys, increased the mortality rate up to 41% from 1990 to 2017 in individuals of all age groups. CKD is responsible for worldwide 1.2 million fatalities per year and decreased kidney function accounts for an additional 1.4 million deaths. 131–133 The rate of kidney dysfunction has increased in the preceding fifteen years. In the event of progressive renal failure, the glomerular filtration rate decreases to less than 15 mL min −1 , giving rise to the retention of metabolic residues, e.g. urea and creatinine, as well as unbalanced serum electrolytes. In healthy individuals, the normal range of creatinine in blood is 45–140 μM per day. 134 Creatinine (Cre) is a vital biomarker for the identification of CKD and other renal disorders since it is elevated in bodily fluids such as saliva, serum, and urine. 135

Saddique et al. 60 synthesized a Cre-imprinted Nb 2 O 5 /PANI nanostructure for the electrochemical sensing of Cre in human saliva. Cyclic voltammetry (CV), differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS) confirmed that the sensor manifests exceptional sensitivity and selectivity for Cre, and improved electron transfer kinetics as compared to pristine non-imprinted PANI. The fabricated Nb 2 O 5 /PANI electrode exhibits a superior sensing capacity of 3.68 μA μM −1 within the linear range of 0–1000 nM remarkably with a very low limit of detection (LOD) of 127 pM and an LOQ of 385 pM. The sensor exhibits excellent selectivity for the biomarker Cre over the common salivary analytes such as glucose, spermine, urea and UA, and ascorbic acid. The sensor showed excellent resilience by retaining 85% of its first reaction over a period of 5 days. Additionally, the designed sensors were evaluated with human saliva samples that are either pure or spiked with different amounts of Cre, with a recovery rate of 97.4 ± 2.83(%).

Spermine

Spermine is a potential biomarker of cancers such as breast cancer due to the abnormal growth of cells, as the level of polyamine is increased in physiological fluids such as saliva. The level of polyamines such as spermine and spermidine in the saliva of cancer patients is 15–20 folds upregulated. Therefore, a POC diagnostics tool is required for onsite and rapid detection of breast cancer. A budget-friendly, sensitive, and portable device was developed for non-invasive diagnosis of breast cancer using saliva.

I. Zaman et al. developed a FeFe 2 O 4 /PPy-based sensor for electrocatalytic oxidation and spermine monitoring in a complex mixture solution of human saliva. Molecular imprinting was employed to make this material selective and sensitive for the targeted analyte spermine. After washing, the cavities were freed to remove any trapped spermine molecule. The sensor exhibited an excellent sensitivity of 0.424 μA nM −1 over a linear spermine concentration range of 0–1000 nM with a very low limit of detection of 220 pM and an LOQ of 667 pM. The sensors demonstrated high selectivity towards spermine compared to other interfering salivary analytes such as guanine, tyrosine, glucose, and ascorbic acid. A stability test at alternate days over a time period of 8 days indicated that the sensor retained 80% of its initial response, which indicated the robust nature of the sensor. The sensor showed 87% response in spiked human saliva samples. Overall, the fabricated device exhibited excellent sensor characteristics. All these figures of merits of FeFe 2 O 4 /PPy confirmed that the sensors showed excellent sensitivity and selectivity only towards the targeted biomarker spermine compared to other polyamines. 136

Glucose

Among the biggest hazards to health initiatives of the 21st century, diabetes mellitus (DM) is alarming. 137 DM is caused by abnormalities in insulin production, and it leads to various diseases such as neuropathy, nephropathy, skin disorders, risk of cardiovascular diseases and dementia. 113 According to WHO predictions, DM and its consequences will claim the lives of over four million adults in 2019, one death every eight seconds. 138 In 2021, there were about 537 individuals with DM. It is anticipated that there will be 643 million DM patients worldwide by 2030. 139 In the past ten years, there were observed remarkable accomplishments in the development of biosensors for potential biomarkers that are crucial for the early identification of prediabetes. Finally, we propose important biomarkers that should be taken into account as possible targets for creating extremely sensitive biological glucose sensors. 140

C. Karaman et al. developed a Ti–Nb 2 O 5 @PPy biosensor for the detection of a glucose biomarker of chronic diabetes. The sensor has an excellent sensitivity of 18.93 μA μM −1 for glucose with a very low limit of detection of 1 μM and an LOQ of 10 μM. A lot of benefits are offered by the biosensor, including its fast processing, high selectivity, and ease of use. Furthermore, a highly selective glucose detection method without any interference in plasma samples was achieved, yielding sensitivity and a detection range of 1.0 × 10 −6 M. Electrochemical techniques such as CV and DPV were performed to access the effectiveness of the sensor. Thus, a new avenue for the assessing of glucose concentration in plasma specimen is made possible by the creation of an enzyme-free glucose sensor rooted on MIPs. As a result, this framework promotes the formulation and exploitation of sensors for glucose in practical applications ( Fig. 10 ). 141

Electrochemical applications

Supercapacitors

Promising technologies such as SCs have attracted some commercial significance in recent decades owing to their potential to significantly impact the market for certain industry-based devices such as smartwatches. 142–144 There are four primary types of SCs that can be distinguished based on how they store charge, namely pseudo-capacitors (PCs), hybrid SCs, asymmetric SCs (ASCs) and electric double-layer capacitors, as illustrated in Fig. 11 . One of the most significant types of SCs, EDLCs, operate by a non-faradic mechanism, as shown in Fig. 12 . Charge buildup appears at the electrode–electrolyte interface of this SC. Graphene and carbon nanotubes, two high-surface-area C-derived constituents, are frequently utilized as electrode materials in EDLC SCs. 145 The second most popular type of SC, known as PC, shown in Fig. 12 , operates via a faradaic process. Redox reactions or intercalation processes are the basis for charge storage in this type of SC. PCs have demonstrated their significant potential to increase power and energy densities when compared to EDLCs. 146

The enhanced redox activity of CPs makes them the most popular electrode material for transition MO x such as Mn 3 O 4 and for PCs. 148 A hybrid supercapacitor (SC), as illustrated in Fig. 13 , combines the advantages of both electric double-layer capacitors (EDLCs) and pseudocapacitors (PCs), offering suitable energy and power densities from the PCs along with high cycling stability and reasonable specific capacitance from the EDLCs. 149,150

Because ASCs offer a broader voltage window than symmetric SCs, they might be considered the third common SC. 151 As such, they have garnered significant attention globally. ASCs have shown both higher energy/power density and greater performance than traditional types of symmetric SCs. 14

Electrolyte is a significant component of electrochemical SCs. They have an electrolyte, two foil electrodes, and a foil separator. SCs and electrolytic capacitors are structurally similar. 152 The separator is placed in between the electrodes after the foil has been rolled into a shape, most frequently cylindrical or rectangular. When the electrolyte is added and sealed, the bent structure is put inside a housing. 153 Unlike traditional electrolytic capacitors, the electrodes and electrolytes utilized in the production of SCs are different. Using porous materials as separators, a SC stores electrical charge and ions at the nuclear level in the holes. 116 An electrolyte is also utilized to connect the two electrodes. Aqueous, chemical, and solid-state electrolytes are frequently used electrolytes. Aqueous electrolytes can increase ionic concentrations and decrease resistances, which increases capacitance and power density. 154 Because of their greater operating potential, organic electrolytes, that is, solutions based on ammonium cyanide, can be used in industrial SCs. Aqueous electrolytes have many benefits over organic electrolytes, as shown in Fig. 14 , including lesser toxicity, greater safety, and cost-effectiveness, even if they have a lower voltage. 142

Owing to their minimal energy density compared to the organic solution, the aqueous solution's limited working potential is one of its most significant drawbacks in application. Significant energy densities are hard to come for these aqueous electrolytes due to their narrow voltage window. The industry is waiting for a more effective energy storage technology to keep up with the rapid advancements in electric cars and other electronic devices. The scale issue and rapid charging are the two main issues facing the EV industry. 155,156

Polyaniline and its composites in SCs

According to Table 6 , PANI is the significant CP which has been widely considered as an electroactive factor for energy storing capacitors, because of its extraordinary qualities, which include high electroactivity, ecological permanence, flexible electrical conductivity, high doping level, high processability, and promising electrochemical characteristics due to different oxidation states. 13 In the realm of flexible smart applications, one of the promising conjugated polymers that has received much study is PANI. 157,158 The use of PANI in smart applications such as gas sensors, 159 biosensors, 160 humidity sensors, 161 temperature sensors, 162 photoluminescence, 163 anti-corrosion, 160 transistors, pressure sensors, 164 LEDs, antenna, electrochromic displays, shape memory, absorbent/water purification, electrorheology, photocatalyst, electrical shielding, SCs, batteries, solar cells, nanogenerators, and fuel cells due to its extensive series of electrical conduction process. 165

Quick charge–discharge kinetics, more economic, appropriate structure, and quick doping-dedoping routes are among PANI's benefits. Furthermore, n-dopable (LiPF 6 ) and p-dopable (HCl) PANIs have a higher power density and a superior resistance to deterioration.

PANI is a valuable material for additional research in the area of high-efficiency SCs because of its property. 179 The majority of published data for polyaniline-based SCs indicate that the charging and discharging process's operational window potential is among 0.8 and 1.0 V. Due to the low energy density achieved, PANI-based SCs with a hypothetical window below 0.6 V are not very appealing. A few research organizations began looking into PANI as an electroactive material for SC applications in the 1990s. Of these, Goswami et al. published the majority of the initial reports, 166 which were then followed by Arbizzani et al. , who picked up steam at the start of the twenty-first century. 180 The majority of reported scientific articles so far have used PANI as a composite form. 166 Moreover, PANI has been noted as an effective SC electrode in the absence of processing composites. Additionally, the only utilized material as electrode is PANI because of its several redox states, which can generate an extensive charge potential when switching between oxidation states during cycles of charging and discharging. 181

For high-grade SCs, Gao et al. have recently described a systematically porous carbon microsphere (SCM)/PANI electrode. SCMs were created by flaming a chitin/chitosan mixture solution, where chitosan was utilized to make the nanopores and nanochannels that made up the microspheres. 182 Another intriguing material for making PANI composite SC electrodes is carbon black (CB). Bavio et al. 183 has stated a comparatively extreme specific capacitance of approximately 1500 F g −1 for SC electrodes with a composite PANI/CB nanostructure. PANI/CB nanostructures were created by simply adding carbon black (0.1 mg mL −1 ) to the polymerization solution's original aqueous dispersion.

S. Goswami et al. 184 have recently reported on the use of CB integrated into the PANI matrix to fabricate a high-performance SC electrode using a PANI nanostructure. The CB that was utilized was made from the carbon waste from regular cooking ovens. 183 Prasanna et al. used a three-electrode setup and a 1 M H 2 SO 4 electrolyte solution to investigate the redox activity of PANI and PANI/SnO 2 nanocomposites ( Fig. 15 ). At 0.48 and 0.35 V, two redox peaks are visible for PANI and the same type of anodic curve with some peak altering is visible for PANI/SnO 2 nanocomposites at 0.22 and 0.6 V. The anodic curve changing, which results from SnO 2 oxidation and electrode resistance, indicates that SnO 2 is present in the nanocomposites. 185

Recent work on carbon nanofibers by Tian and colleagues produced N-doped carbon nanotubes/PANI composites. Based on the categorized core-sheath structure of N-CNT/PANI/CNT fibers, they developed a wearable SC that, after 10 000 series, has a specific capacitance of about 320 F g −1 at 1 A g −1 over 92% of the retaining factor. 175 SCs are made flexible by a well-aligned CNT fiber, and their permeable N–carbon nanotube structure considerably facilitates the relocation of ions and electrons that improve their storage behavior. Clothing made from carbon fibers or nanofibers has a lot of potential as an electrode material for malleable SCs due to its elevated electrical conductivity, large surface area, and good chemical strength. However, a straightforward and inexpensive method can be used to readily build a PANI nanostructure on carbon fibers for use as a variable SC electrode. 186

PANI and its application in batteries

PANI has been extensively studied for over 150 years in various applications due to its wide range of functions, and it was only around fifty years ago that PANI was 1st used in an electrochemical application. Chemical doping is a natural method for CPs such as PANI to change from insulators to semi-metallic conducting. 187 PANI and its derivatives are used in batteries because of their ability to conduct metals and function as lenient polymeric networks that provide high elasticity, exceptional mechanical power, and simple functionalization synthesis. Therefore, PANI is being looked into as a possible cathode material option for LIBs, as explained in Table 6 . 188

As compared to PANI with other CPs, such as PPy and Poly(3,4-ethylenedioxythiophene) has capacity of 114 and 115 mA h g −1 , reveals that PANI has a complex hypothetical capacity (294 mA h g −1 ) as LIB cathode material. LiPF 6 , LiBF 4 , Zn(ClO 4 ) 2 , LiClO 4 and other ionic salts have been used as dopant materials for PANI in order to create the cathode electrode for LIBs. 189

Additionally, sophisticated hybrid cathode materials that combine PANI with organic and inorganic materials such as LiMn 2 O 4 , MOS 2 , graphene (G), V 2 O 5 , LiFePO 4 , polyoxometalate, or reduced graphene (rG) are being investigated as a way to recover the electrochemical characteristics of battery cells. Ajpi 188 and colleagues have found that when LiFePO 4 (120 mA h g −1 ) or pristine PANI (95 mA h g −1 ) cathode systems are compared, the hybrid LiFePO 4 @PANI exhibits a substantially enhanced capability of 145 mA h g −1 at a redox rate of 0.1C. Hybridization causes the contact resistance to decrease, which speeds up the diffusion of lithium cations to the electrolyte and the transmission of electrons to the collector along the polymer chain. 116,163,190 In addition to the electrode component used in LIBs, PANI-based hybrid composites have been developed for lithium sulphur (Li–S), aluminum (AIB), sodium (SIB), zinc ion batteries (ZIBs), and ammonium storage cells, among other battery cell types. 159 Huang et al. , for example, reported on the production of PANI-inserted MnO 2 nanolayers with 40% utilization rate using them as the cathode material for Zn–MnO 2 rechargeable devices. 14 The nanolayers were stabilized for 5000 cycles using a slight aqueous electrolyte. Additionally, a number of studies have been published on PANI composites for magnesium-ion batteries. 159,191 Wang et al. have recently revealed that a flexible cathode for MIBs using PANI nanoarrays and carbon cloth has 97.25% retention capacity at 1 A g −1 after 1500 phases. 171 However, Krishna et al. have revealed that PANI has electrocatalytic action in Mg–S batteries. The MgS x catalyst was loaded onto pristine carbon cloth (CC) to create one electrode, while the PANI-coated carbon cloth was used to create the other. The superior electrochemical performance of MO x @PANI is attributed to improved electrical conductivity due to synergetic effects, enhanced lithium ion diffusion and good structural stability, which make it an excellent candidate for battery applications ( Table 7 ). 192

PPy and its composites in SCs

One of the CPs that is most typically utilized for a range of applications is PPy. The electrochromic effect based on electrochemical polymerization conditions, solid absorptive characteristics towards DNA, gases, and proteins, corrosion-free qualities, redox activity, catalytic movement, capacity to synthesize nanowires through conductivity ranging between 10 −2 and 10 −4 S cm −1 at 27 °C, ion discrimination skills and ion exchange, charge/discharge methods, and electrochromic effect define this polymer's versatility.

Most of these characteristics are based on the makeup of the dopant as well as the synthesis method. Electrochemical synthesis and deposition of PPy are possible on the conducting surfaces. The low cost, easy fabrication, high conductivity, customizable doping/dedoping features, and extensive range of uses of PPy have drawn several investigation considerations in fields such as electrical devices, sensors, and energy storage devices. Of the several CPs, PPy is the one that has been studied the most because of its favorable redox properties and ease of manufacture. Because of the powerful intrinsic qualities listed above, PPy has great potential for various applications including sensors, artificial muscles, batteries, SCs, and microwave shielding. This well-known PC can store more charge because of the inherent properties of the faradaic storage technology. 116

PPy-based material composites are extensively researched for many uses. Owing to its important characteristics, such as high conductivity, high capacitance, and low density, PPy can be employed as a material that works well for SC applications. Chemical and electrochemical processes are the primary means of developing PPy. When a large amount needs to be generated, chemical synthesis is performed, and potent oxidizing agents are required. Electrochemical production is recommended for research purposes due to its ease of use, precision in controlling material thickness, geometry, and position, flexibility in doping materials during synthesis, accessibility to a wide range of dopant ions, and production of high-value films. It creates adherent surface uniform deposits when monomer units are in a bulk solution. 196,197

Younghee and colleagues analyzed the development of a unique 3D hybrid nanoarchitecture by physically inserting monodisperse PPy nanospheres as client species into piled graphene layers without significantly altering their appearance. At a weight ratio of 8/1 between PPy and graphite, the precursor of graphene, the graphene/particulate PPy (GPPy) nanohybrids showed excellent electrochemical functioning in relation to charge transfer resistance, chemical reaction activity and Cs. This was influenced by the proportions and makeup of the PPy tiny spheres. Bulkiness or density of packing dictated the execution result of the electrode materials. Using an acidic electrolyte, flexible and solid-state hybrid capacitor cells showed outstanding electrochemical accomplishment, with a maximum energy density of 8.4 W h kg −1 or 1.9 W h L −1 and a maximum power density of 3.2 kW kg −1 or 0.7 kW L −1 . The cesium in the 6 mol L −1 KOH solution is approximately 433 F g −1 at the optimal PPy intensity in the PPy/C aerogel nanocomposite (35 weight percent of PPy). This is due to the substance of the nanocomposite's double-layer and redox capacitive behaviour working together. Activated carbon (AC) and PPy composite electrodes show relatively high cesium, or 45.1 F g −1 , in a separate report by Thakur et al. This is approximately twofold as high as other standard SCs based on activated C electrodes. 198

PPy/NiCoHCF (nickel-cobalt hexacyanoferrate) was synthesized by Wu et al. using an electrochemical process with an inexpensive corrosion-resistant steel template. The findings demonstrate that by adding NiCoHCF to PPy, its charge storage qualities were enhanced in both non-aqueous and aqueous environments. The proposed nanocomposite, based on the galvanostatic charge–discharge method, could achieve extreme charge storage capacities of 529 and 668 F g −1 in both aqueous and non-aqueous ionic solutions. Additionally, at a current density of 10 A g −1 , the nanocomposite showed a remarkable specific energy density of 87 W h kg −1 , a remarkable specific power density of 5600 W kg −1 , and excellent strength with <10% loss after 1000 cycles. The conclusion indicates that the suggested nanocomposite could be a valuable electrode material for electrochemical SCs. 199

SCs ability to supply at high momentary durations has led to their use as electrical energy storage devices. Nanocomposites composed of MoS 2 , graphene, PPy, and other filler elements are the advanced items for SC purposes. The exceptional electrical conductivity and higher surface volume of these materials, which are essentially 2D, allow them to function exceptionally effectively in SCs. 200 SC applications of numerous MO x @PPy-based composites are discussed in Table 6 .

Electrocatalytic applications

The sensible creation of long-lasting, highly effective catalysts that are also reasonably priced and readily available is essential to electrocatalytic water splitting. Therefore, it is necessary to have an effective electrocatalyst that can successfully follow the electrolytic catalysis of the HER and OER. 18 Fuel cells, which operate on hydrogen or H-rich fuels and release little CO 2 , have become potential energy conversion technologies. 87 The superior qualities of membrane fuel cells (PEMFCs) and proton trade, including their extreme energy conversion efficacy, elevated open-circuit potential, partial fuel edge properties, and effective low-temperature electrochemical oxidation of natural molecules such as ethanol, methanol, and formic acid have drawn more attention to them than to the others. 201 Furthermore, the fuel cell's stability and efficiency have been linked to the enhanced 3-phase interface, which consists of an ionomer—an ionic solution membrane—attached to the surface of the catalyst. At the solid–electrolyte interface, protons are available to the electrolytic stage and react with O 2 after initially reacting with the anode's solid phase and hydrogen gas molecules. 202 Therefore, creating stable, affordable electrocatalysts and polymer membranes, as well as comprehending the efficiency of small organic molecules' catalytic activity, is essential for fabricating fuel cells that are both large scale and economic. 19

For fuel cell applications, CPs such PPy, PANI, poly-3-methyl thiophene (PMT), and PEDOT have been effectively employed as electrocatalyst-supporting materials. The unusual, conjugated architectures of CPs, which have remarkable chemical strength, extreme electrical conduction, ease of production, and cheapness, have shown promise in their use as catalytic supports. 203 The electrolytic oxidation of tiny molecules including H, CH 3 OH, and HCOOH has thus been accomplished ( Fig. 16 ), employing CP-based nanohybrids, which are composed of a succession of metal or MO x added on the surface of the polymer. Recent efforts to develop electrode materials have involved the direct deposition of nanostructured metal catalysts on CP substrates or on customized polymer nanostructures. 204 Hydrogen's exceptional qualities make it a desirable clean energy source. 205 Hydrogen has zero emissions when used as a fuel because it generates energy with just water vapor as a byproduct. 206 This special quality makes hydrogen a strong candidate in the drive to decarbonize in various fields 207 including power generation, 191 transportation, 208 and industries.

Apart from its advantages for the environment, hydrogen has a high energy density that can compete with traditional fossil fuels. 209 Because of this feature, it is a desirable choice for applications where transportation efficiency and energy storage are crucial. A move towards alternate feedstocks, such as wastewater and saline water, which not only provide a sustainable resource but also pose unique problems that call for creative solutions, has been spurred by the necessity to match hydrogen production with sustainability objectives. 210 Researchers are looking into unusual water sources, especially wastewater and salt water, as possible feedstocks in the pursuit of sustainable hydrogen synthesis. 211 Although these sources provide a plentiful and sustainable supply, using them presents a number of complex issues that need creative solutions for effective and ecologically conscious hydrogen production. Complex Chemistry of Water: The chemical compositions of wastewater and saline water are frequently complicated and varied, containing dissolved ions, pollutants, and impurities. 212 Designing catalysts and procedures that may effectively and selectively extract hydrogen while minimizing undesirable side effects is difficult due to this intricacy. Corrosion and fouling: equipment and catalysts may corrode and foul due to the corrosive properties of salty water and the presence of contaminants in wastewater. 177

Hydrogen evolution reaction

The most significant method for archiving the next creation of green power is the HER, which is the cathodic reaction in the H 2 O-splitting route. 105 In addition to Pt, which is the utmost potent HER catalyst in acidic media, a number of low-cost metal phosphides, nitrides, transition metals (TM), and TM dichalcogenides have been investigated as possible HER catalysts in alkaline media. 213 Due to their reduced asset costs when contrasted to acidic electrolytes that depend on Pt or alkaline electrolyzer, additional noble metal-based electrocatalyst development is being actively studied. 214 CPs are becoming competitive alternatives to the HER as both photocatalysts and electrocatalysts, despite the fact that a majority of studies on novel electrocatalysis resources have concentrated on TM-based reagents. For example, in order to create keto-indoleamine hydrogen bonds, polydopamine (PDA) was successfully altered with indoleamines, giving the HER a favorable H adsorption energy. 215

According to the DFT simulations, this bond, which is created when o-dopamine quinone and aminochrome parts are linked, shows hydrogen bonding near zero and is said to be advantageous for driving the HER. 216 Moreover, the HER activity can be further adjusted to attain CP performance equivalent to Ni by varying the degree of functionalization. Similarly, two pyridinic N were added to the structure of dibenzo thiophene sulfone, which improved the resulting polymer's photocatalytic activity. In a different investigation, PPy doped with I2 demonstrated competent activity as a supporting electrode for the HER. 171 Additionally, I2 doping produced electrodes with higher conductivity and stability. MoS 2 /PANI was produced by Ding and colleagues by combining MoS 2 nanosheets with the PANI matrix, which was earlier made using a hydrothermal technique. With an optimal composition that contained 19 wt% of PANI, the MoS 2 /PANI composite demonstrated a higher activity than that of MoS 2 . Even though MoS 2 aggregation reduced the number of effective sites, the greater electric conduction resulted in better performance. Likewise, Torres and associates created Ni/PANI hybrid electrodes by electrodepositing Ni in dissolved PANI. 217 These conductors showed a thirty percent increase in electrical conductivity at 100 mV vs. RHE in an alkaline electrolyte associated with the bare Ni substrate because of enhanced nickel dispersal in the PANI matrix, which promotes H-movement to the Ni sites. A similar process was utilized to produce Pd/PANI or Pd/PEDOT nanocomposites. 218

Furthermore, CPs have been used with additional materials to produce hybrids that work together as TM-based catalysts. For instance, PANI was coated on Na 4 Ge 9 O 2 to support Pt nanoparticles, and Ir has been reinforced with TiO 2 /TiO 2 -WO 3 essential elements to create hybrid sustenance for NiP. For the latter, a reported 80 mV drop in overpotential was ascribed to PANI's electrical conductivity in the alkaline electrolyte in a deprotonated form. Furthermore, PPy was used to encapsulate carbon nanotubes (CNTs), which helped immobilize and disperse Co 3 O 4 nanoparticles . 219 The polymerization of CPs using electrochemical or organic pathways with the inclusion of NPs or additional components is another widely used method. For instance, aniline was electro-polymerized on Ni foam-supported zeolite to create a PANI/zeolite/nickel froth cathode. 220 The HER activity was increased when zeolite/Ni was coated with enough PANI layers, highlighting the significance of managing the polyaniline amount and coatings generated to attain peak execution exclusive of blocking availability to the zeolite's functional sites. Similarly, deposited monomers on NiCoP films were polymerized to cover PSS:PPy on NiCoP. By altering the metal atoms' electrical structure and surface shape, this technique made it possible to tune the activity of HER of NiCoP. Likewise, FeCo 2 O 4 @PPy, FeCo 2 S 4 @PPy, ZnWO 4 @PPy and Na 4 Ge 9 O 2 @PANI were found to have enhanced activity as a result of hybridization. 221

Wang et al. showed that using organometallic materials to create polymeric complexes functional for the HER is a noteworthy tactic ( Table 8 ). They created porphyrin Co parts, and Co that was linked to an imine ring performed better in the HER. Pyrolysis can be used to create a specific metal-like catalytic agent on the structures of carbon from metals that are widely distributed in a polymeric matrix. 221 Metallopolymers having a metal at the center linked to ligands holding heteroatoms that are nitrogen or sulphur are created using the commonly used post-calcination synthesis technique. In comparison to cutting-edge metal-based catalysts, calcined catalysts are typically more competitive and have greater HER activity than the non-calcined ones. CPs function as precursors in this case, losing their structure when calcined. 109

Mendoza et al. claimed that techniques that incorporate metal traces on the CP scheme, polymer covering of metal NPs, or immediate polymer and NP manufacturing are generally more efficient than simple routine mixing. To achieve structures that support charge passage, especially ion flow across the complete conductor, material production must be optimized. Thick polymer films may make it harder to reach the metal sites, even though coating polymers on transition metal NPs can improve the intrinsic activity and electrode conductivity of metal nanoparticles. Thus, one of the biggest obstacles to producing more active composite materials is still developing interfaces in nanocomposites. 222

Oxygen reduction reaction

Power transformation equipment such as fuel cells and batteries made of metallic-air depends on the ORR, a process that is critical to biological systems and necessary for maintaining life. 177 Because the ORR at the cathode has a slow kinetic, it has a substantial impact on the device efficiency of proton exchange membrane fuel cells, particularly direct methanol booths. 233 Triplet molecular oxygen's (O 2 ) distinct electrical structure is the cause of this slow reaction. Antibonding impoverished molecular orbitals are occupied by unpaired electrons, which prevent new electrons from entering. In order to promote electron transference and lower extreme potential involved in the ORR, catalysts that dynamically adsorb molecular oxygen must be improved. 234

The ORR can move forward via either an outer-sphere or an inner-sphere process. Through a two-electron transfer, the outer-sphere mechanism produces H 2 O 2 as the only product. Simultaneously, synergistic or disruptive assimilation of the molecular O 2 atom is a part of the inner-sphere mechanism. Although the last splits the O–O bond to produce H 2 O with four-electron transmission, the first maintains the oxygen–oxygen bond and produces H 2 O 2 (two-electron transfer). The favored channel for CPs is a two-electron transfer. CPs frequently behave as electron donors, transferring charge to bound oxygen molecules in a powerful way. By changing the molecular symmetry and lengthening the O–O bond, this interaction activates oxygen. Furthermore, CPs can oxidize to a significant degree, converting absorbed O 2 to O 2 (ref. 134 ) The increased catalytic activity of nanocomposites made with metal NPs and CPs is frequently ascribed to the interaction of the metal activity with the increased electrical permeability of the matrix of polymeric material within the electronic potential border. 163

Zhou and companions used polypyrrole and the TM oxide MnCo 2 O 4 to create an ORR catalyst. Interfacial polymerization with oxidative chemicals was used to fabricate the material. Using RRDE analysis, they confirmed that when PEDOT was used alone, the reaction process changed from a 2-electron transport to a 4-electron movement once the material was included into the matrix of the polymer. Using cyclic voltammetry to evaluate the substance's firmness, they discovered that the hybrid-modified transparent carbon electrode retained signal integrity even after 500 cycles of applied potentials between −1.0 and +1.0 V. 235 The overpotential was lower in electrochemical experiments than in each MnCo 2 O 4 and PPy materials. Additionally, instead of the limited 2-electron transference seen when utilizing only the polymer, they found a 4-electron transfer channel employing a rotating ring-disk electrode (RRDE). 227 The electrocatalytic performance showed impressively little alteration (1%) even after 16 h of continuous process. By mixing PEDOT with CoMn 2 O 4 in a wet manner, Chowdhury et al. created a hybrid catalyst for the ORR. There was an overpotential of −870 mV in the resulting composite material. 236

O 2 evolution reaction

The OER is a vital electrolytic route that is essential to the parting of H 2 O to produce H. Because of extremely corrosive circumstances, this several-phase method which involves the movement of 4 protons connected to 4 electrons stays slow and complicated, exhibiting large overpotentials and restrained strength. 237 The continuous search for long-lasting and efficient OER electrocatalysts has drawn a lot of attention towards TM-based catalysts, particularly spinel oxides, TM hydroxides, and perovskite oxides, which are prized for their remarkable activity and affordability. 238 Improving these materials' conductivity and stability is still crucial, though. An interesting approach in this regard is to incorporate conductive materials such as CPs into these electrocatalysts to improve stability and promote charge transfer. Numerous composite materials made of polymers and MO x have been described recently. To fully utilize CPs' potential as OER electrocatalyst components, more research is necessary. 229 MnCo 2 O 4 /PPy, CoFe 2 O 4 /PPy, Co 3 O 4 /PANI, Co–Fe/PANI, Co 3 O 4 /PEDOT, Co/PTh, NiO/poly(3-hexylthiophene), Co 2 (OH) 3 /Poly(3-bromo-thiophene), MnCo-oxides/PEDOT, and Co 3 O 4 -polyethyne have all been produced through various techniques. 192 Enhanced catalytic efficiency of the hybrid electrolytic catalysts has been observed in these research studies.

This improvement is ascribed to the many electrical routes provided by the CPs, the modifying-tuning of the activity of metal catalytic routes, and the more extensive contact and dispersal of functional sites made possible by a matrix made of polymers. 91 Using MnCo 2 O 4 -NPs with PPy, for example, Cao et al. chemically polymerized pyrrole with H 2 O 2 while the NPs were present to generate a composite. They found that the hybrid substance surpassed pristine materials in the OER, with an extreme potential of about 480 mV, which is similar to the benchmark for RuO 2 /C (20%). 239

The inclusion of PPy was attributed to the enhanced stability since it stopped MnCo 2 O 4 -NP corrosion and NP aggregation. Prior research on Co 3 O 4 nanoparticles and PPy hybrids has clarified that the electrocatalyst's structure has a major impact on the composite's performance. 240 The most functional catalyst, they discovered, showed a great accessibility of Co-involved regions scattered throughout the matrix of polymers with an ideal CP quantity. A departure from this ratio caused the CPs to impede Co sites and cause nanoparticle aggregation. 160 A synergistic interaction is achieved by optimizing the molecular proportions of the composite components, which is echoed in other research studies producing Co 3 O 4 /PEDOT, Co 3 O 4 /Polyethylene, and Co 3 O 4 /PANI. 241

Photocatalytic activity of PANI/ZnO hybrids

ZnO is a semiconductor of the n-type oxide that is eco-stable and nontoxic, with a high photo-activity and a strong bandgap energy. 242 It has the potential to acquire a unique and noteworthy capacity for photocatalysis over time, fascinating an important share of the solar band and exhibiting suitable photooxidation efficiency, including organic contaminants that are hazardous and non-biodegradable. ZnO, along with different semiconducting metal oxides, has several benefits and is a material that is good for the environment. 242 It is used in everyday applications without endangering the health of people or other living things. ZnO has good electrical features, strong mechanical capabilities, and great optical qualities. It is also less expensive than TiO 2 NPs, which makes it a popular choice for large-scale operations. Fortunately, since light absorption is essentially limited to the UV range, ZnONPs' primary drawback is linked to their restricted spectral response. 243 As a result, significant efforts have been made to address both this drawback and the great characteristic potential of photogenerated charge carrier recombination. It is well known that the shape and morphological characteristics of semiconductor oxides have a significant impact on their ultimate photocatalytic efficiency. 244

Representing the fabrication of novel and potent photocatalysts, which are distinguished by an efficient partition of the charge transferors, tremendous work and understanding of the requirements needed for synthesis are consequently essential. Superior consistency and reusability performance were achieved along with improved light absorption and volume-to-surface ratios. The primary characteristics are the final project's universality, the management of agglomeration and accumulation, and the removal of an infinite number of particles of catalyst following the photocatalytic phase in many stages. 245

As previously stated, PANI, which is regarded as the most possible polymer systems for enhancing both the electrocatalytic and photocatalytic characteristics of ZnONPs, has drawn a lot of attention in a number of published studies aimed at boosting the photocatalytic effectiveness of ZnONPs through Vis-light. The fact that practically all of the works describe cationic methylene blue dye as an ecologically hazardous substance for examining the photocatalytic effects of blue light and UV radiation at room temperature is another intriguing finding. 246 Using an extreme amount of MB at a constant reaction rate, Qin et al. 245 found a higher photocatalytic activity of a nanocomposite based on PANI-ZnONPs. An in situ chemical polymerization method was used to synthesize the PANI-ZnO hybrids, which serves as a necessary step in producing an effective photocatalyst. Additionally, the glassy carbon electrode was decorated with the resulting PANI-ZnO nanocomposite, and the potential of the PANI-ZnONPs/GCE terminal assembly as a microbial anode for fuel cells was also evaluated. PANI/ZnO nanocomposites were prepared by Asgari et al. in another published study. 247

The observed outcomes of the photocatalytic reaction under visible light illumination suggest that the PANI/ZnONP catalyst surface has significantly degraded the MB dye. When it came to the destruction of the MB dye, the PANI/ZnO hybrid system demonstrated three times the photocatalytic activity of pure PANI. Similar to this, Rajeswari et al. created a nanocomposite consisting of PANI/ZnO and investigated its potential as a photocatalyst for the degradation of two dyes, MB and malachite green, in the occurrence of UV-Vis sunshine. The results demonstrated that a modest quantity of PANI/ZnO nanocomposite photocatalyst destroys all dye solutions (MB or MG) with 99% effectiveness after 5 hours of exposure to natural sunlight. 248

The PANI/ZnO nanocomposite's photocatalytic capabilities for the artificial, broad-band antiseptic, non-decomposable, and highly H 2 O-soluble breakdown of metronidazole (MNZ) were explained when exposed to UV and visible light. Consequently, there has been a lot of interest in treating wastewater before releasing MNZ into the environment. This work's challenge was to use a synthetic PANI/ZnO nanocomposite to eliminate MNZ from wastewater. 249 According to the data, the PANI/ZnO-based nanocomposite degraded MNZ at a pace more than 60 times faster than the plain ZnONPs photocatalyst. The significance of hydroxyl and superoxide anion radicals in the quick breakdown of MNZ is highlighted in Fig. 17 . 250

Future perspectives

While previous studies have provided significant insights into MO x @CP composites, they have primarily limited on specific applications. The novelty of this review lies in its interdisciplinary approach, covering diverse areas such as biomedicine, energy storage, and electrocatalysis. Moreover, this work reinforces the synergy between synthetic strategies and functional performance, offering a roadmap for the systematic design of innovative MO x @CP materials.

The features of innovative materials can be adapted to suit particular applications through the appropriate use of copolymerization, cross-linking, and ligand attachment. Further endeavors to foster interdisciplinary collaboration and create cutting-edge polymerization methods that reduce heterogeneity, enhance toxicity, and reduce manufacturing costs are desirable in the future. Despite the notable progress in MO x @CP hybrid materials, various critical challenges must be addressed for their extensive adoption. Major obstacles involve complex protocols, high cost, and limited reproducibility at an industrial level. Developing an AI-driven material design, i.e. AI-designed CPs 251 and automated high-throughput screening, could facilitate the discovery of refined composites with enhanced performance. In addition, green synthesis routes such as solvent-free polymerization and bio-inspired fabrication are vital to uphold sustainable production while reducing environmental impacts. 252

In biomedical applications, the toxicity of CPs and MO x remains a key challenge, markedly for in vivo applications. Even if not all MO x and CPs are resolved to be biologically safe, toxicity studies are currently being conducted. 253 Problems with sensor disposal, affordability, simplicity of manufacture, large-scale synthesis, and recycling must be tackled and resolved. In the light of electrochemical biosensors that provide a simple means of determining the concentrations of dangerous and harmful substances in the ecosystem, for public welfare and food security, monetization of these technologies is a crucial factor that needs to be considered. Sensors based on PANI integrate the feature of nanostructures and CPs. The primary issues preventing PANI from being widely used include non-degradability, insufficient solubility and improper processability. 157 As the need for quick, precise, and minimally invasive POCT devices for managing diabetes grow, new biosensing molecules are being discovered, improved, and created based on the subsequent advancements in technology. Because the majority of POCT devices for insulin and pancreatic hormone glucagon rely on retail available antibodies, there will be fewer sensing methods and devices available. As a result, there will be less flexibility in the selection of biosensing molecules, which will restrict the development of novel technologies in this area in the future. 254

Although they face a number of significant obstacles, MO x @CPs hybrids have a lot of potentials for electrochemical systems such as batteries and SCs. A significant challenge is maintaining stability over time under multiple charge–discharge cycles since physical and electrochemical stresses frequently cause component separation or structural damage. Another challenge involves reconciling the compromise between substantial power density (from CPs) and high density of energy (from MO x ), since maximizing one characteristic frequently puts the other at risk. Moreover, the inherent constraints of certain hybrids that usually have low conductivity might reduce the effectiveness of charge transfer. The synthesis of high-performance hybrids still faces challenges with scalability and cost-effectiveness, particularly when utilizing scarce precursors or intricate fabrication techniques. The creation of recyclable designs and green synthesis pathways is also necessary to ensure sustainable practices in their manufacturing and disposal, hence reducing their ecological mark. In order to overcome these obstacles, a multidisciplinary strategy combining materials research, engineering, and electrochemistry will be needed. 13

MO x -CP hybrids have promise, but there are a number of issues that must be resolved before they can be widely used in electrocatalysis. One major concern is how stable these hybrids will be over time in challenging operating environments including high voltages, high temperatures, and extreme pH, which can degrade materials and reduce catalytic activity. It is still technically challenging to achieve evenly dispersed and strong interface bonds among MO x and matrix polymers because inadequate integration might impede electron transport and lower overall performance. Scalability is a further issue because large-scale production is restricted by the complexity, expense, and time required for the present synthesis processes. Furthermore, despite the fact that catalytic activity optimization has advanced significantly, commercial feasibility is still hampered by the conflict between efficiency and material cost. To overcome these obstacles, new material designs, scalable and environmentally friendly synthesis methods, and a deeper knowledge of mechanisms through experimental and computational methods will all be necessary. 232

Conclusion

In summary, MO x @CPs represent a promising class of multifunctional materials with revolutionary potential in biomedicine, energy storage, and environmental technologies such as photocatalytic water splitting. Their synergistic integration enables significant improvements in electrical conductivity, chemical and thermal stability, biocompatibility, and catalytic activity, making them ideal candidates for applications such as disease diagnosis, supercapacitor fabrication, and efficacious hydrogen production. This review emphasizes not only the recent advances in synthetic techniques—including in situ polymerization, sol–gel processing, and electrochemical deposition—but also the tunability of these materials for specific applications. Despite the impressive progress that has been made, several challenges persist, particularly in achieving uniform dispersion, enhancing interfacial compatibility, and scalable fabrication techniques. Sustained innovations in synthesis methods and material optimization will further unlock their full potential, progressive augmentation in these critical fields. Future research endeavors should prioritize designing smart and stimuli-responsive hybrids tailored for real-time biomedical applications. Additionally, machine learning and AI are integrated to predict the structure–property relationships for efficient rational design. With ongoing advancements in material design and fabrication techniques, MO x -enhanced CP hybrids are equipped to make remarkable contributions to the development of viable technologies across various industries.

Data availability

No primary research results, software or code has been included and no new data were generated or analysed as part of this review.

Conflicts of interest

There are no conflicts to declare.

Biography

Mariam Akhtar is a dedicated researcher in the field of chemistry, with a strong emphasis on material synthesis, sensor development and diagnosis. Born in January 2000 in Pakistan, she completed her BS (Hons.) in Chemistry in 2018 at Government College University, Faisalabad. She completed her MS in Chemistry from the University of the Punjab Lahore Pakistan in 2024 with distinction. She conducted her research in Sensors and Diagnostic Lab, School of Chemistry https://aafzal.net/team/ . During her academic career, Mariam worked under the guidance of Prof. Dr M. R. S. A. Janjua, contributing impactful review articles. Her research expertise lies in advanced polymer composites doped with metal oxides and porous materials, including metal–organic framework (MOF)-derived composites. Her research holds significant potential in energy storage, catalysis, and environmental sustainability. Her passion for innovation and interdisciplinary research drives her to pursue PhD studies in polymers and sensor devices, aiming to advance cutting-edge solutions in material chemistry.

Biography

Sehar Shahzadi is an emerging researcher in the field of chemistry, with a strong focus on materials science and nanochemistry. Born in January 2001 in Pakistan, she completed her BS (Hons.) in Chemistry in 2022 and her MPhil in Inorganic Chemistry in 2024 at Government College University, Faisalabad, graduating with distinction. During her academic career, Sehar worked under the guidance of Prof. Dr M. R. S. A. Janjua, contributing to several impactful review articles. Her research expertise lies in the synthesis and characterization of advanced materials, with a particular emphasis on metal–organic framework (MOF)-derived carbon composites and nanocomposites. Her work has potential applications in energy storage, catalysis, and environmental sustainability. Motivated by a passion for innovation, Sehar is actively seeking PhD opportunities to deepen her expertise in nanochemistry and materials science.

Biography

Muhammad Arshad, born in January 1999 in Pakistan, is a rising chemist and educationist with a strong background in inorganic chemistry. He earned his bachelor's degree in Inorganic Chemistry from Government College University, Faisalabad, in 2022. His research focuses on advanced materials, particularly MOF-derived carbon composites and nanocomposites, and he has contributed to notable publication in the field. Mr Arshad is currently working under the guidance of Dr M. R. S. A. Janjua, gaining expertise in material synthesis, characterization, and their applications in catalysis, energy storage, and environmental sustainability. Driven by a passion for innovation and discovery, he is actively seeking PhD opportunities to further his research and make meaningful contributions to the field.

Biography

Tahreem Akhtar is an emerging researcher in biochemistry with a strong passion for scientific discovery and innovation. She was born in 2003, in Pakistan. She is pursuing BS (hons) in Biochemistry at the University of Veterinary and Animal Sciences, Lahore. Tahreem is currently working under the guidance of Prof. Dr M. R. S. A. Janjua, focusing on biochemical research with potential applications in health, addressing critical challenges in disease diagnostics. With a deep curiosity for molecular sciences and biochemical processes, she is dedicated to expanding her expertise through MPhil research.

Biography

Muhammad Ramzan Saeed Ashraf Janjua began his professional career as a Medical Representative at Johnson & Johnson Pharmaceuticals and Sanofi-Aventis in early 2001. While working in the pharmaceutical industry, he earned an MBA in Marketing from PIMSAT and MSc in Chemistry from the University of Sargodha, Pakistan. He was later awarded a joint PhD scholarship by the governments of China and Pakistan, completing his PhD in 2010. Dr Janjua served as an Assistant Professor at the University of Sargodha before pursuing a postdoctoral fellowship at the University of Coimbra, Portugal. He subsequently joined KFUPM, KSA, where he was promoted to the rank of full Professor in 2022. In the same year, he returned to Pakistan and joined GCUF as a Professor of Physical Chemistry, where he also serves as the Director of International Linkages.

References

Namsheer K. Rout C. S. Conducting polymers: a comprehensive review on recent advances in synthesis, properties and applications RSC Adv. 2021 11 10 5659 5697 35686160 10.1039/d0ra07800j PMC9133880

Le T.-H. Kim Y. Yoon H. Electrical and electrochemical properties of conducting polymers Polymers 2017 9 4 150 30970829 10.3390/polym9040150 PMC6432010

Guo X. Facchetti A. The journey of conducting polymers from discovery to application Nat. Mater. 2020 19 9 922 928 32820293 10.1038/s41563-020-0778-5

Nezakati T. Seifalian A. Tan A. Seifalian A. M. Conductive polymers: opportunities and challenges in biomedical applications Chem. Rev. 2018 118 14 6766 6843 29969244 10.1021/acs.chemrev.6b00275

Yang L. Yang L. Wu S. Wei F. Hu Y. Xu X. et al. , Three-dimensional conductive organic sulfonic acid co-doped bacterial cellulose/polyaniline nanocomposite films for detection of ammonia at room temperature Sens. Actuators, B 2020 323 128689

Abhishek N. V. A. Singh A. Kumar T. Metal-conducting polymer hybrid composites: A promising platform for electrochemical sensing Inorg. Chem. Commun. 2023 154 111334

Nguyen D. N. Yoon H. Recent advances in nanostructured conducting polymers: from synthesis to practical applications Polymers 2016 8 4 118 30979209 10.3390/polym8040118 PMC6432394

Tian W. Liu X. Yu W. Research progress of gas sensor based on graphene and its derivatives: A review Appl. Sci. 2018 8 7 1118

Farka Z. Jurik T. Kovar D. Trnkova L. Skládal P. Nanoparticle-based immunochemical biosensors and assays: recent advances and challenges Chem. Rev. 2017 117 15 9973 10042 28753280 10.1021/acs.chemrev.7b00037

Jafari S. Dehghani M. Nasirizadeh N. Azimzadeh M. An azithromycin electrochemical sensor based on an aniline MIP film electropolymerized on a gold nano urchins/graphene oxide modified glassy carbon electrode J. Electroanal. Chem. 2018 829 27 34

Shoaie N. Daneshpour M. Azimzadeh M. Mahshid S. Khoshfetrat S. M. Jahanpeyma F. et al. , Electrochemical sensors and biosensors based on the use of polyaniline and its nanocomposites: A review on recent advances Microchim. Acta 2019 186 1 29 10.1007/s00604-019-3588-1 31236681

Saddique Z. S. Maleeha F. Muhammad B. Sadia Z. Mujahid A. Afzal A. Core–shell niobium(V) oxide@molecularly imprinted polythiophene nanoreceptors for transformative, real-time creatinine analysis Nanoscale Adv. 2024 6 15 3644 3654 38989513 10.1039/d4na00300d PMC11232539

Vinayak V. V. Deshmukh K. Murthy V. Pasha S. K. Conducting polymer based nanocomposites for supercapacitor applications: A review of recent advances, challenges and future prospects J. Energy Storage 2024 100 113551

Zhang S. Shi X. Chen X. Zhang D. Liu X. Zhang Z. et al. , Large-scale and low-cost motivation of nitrogen-doped commercial activated carbon for high-energy-density supercapacitor ACS Appl. Energy Mater. 2019 2 6 4234 4243

Gautam K. P. Acharya D. Bhatta I. Subedi V. Das M. Neupane S. et al. , Nickel oxide-incorporated polyaniline nanocomposites as an efficient electrode material for supercapacitor application Inorganics 2022 10 6 86

Yesuraj J. Padmaraj O. Suthanthiraraj S. A. Synthesis, characterization, and improvement of supercapacitor properties of NiMoO4 nanocrystals with polyaniline J. Inorg. Organomet. Polym. Mater. 2020 30 2 310 321

Babel V. Hiran B. L. A review on polyaniline composites: Synthesis, characterization, and applications Polym. Compos. 2021 42 7 3142 3157

Tawfeek A. M. Jabbour K. Abid A. G. Nisa M. U. Manzoor S. Shabbir B. et al. , Sm2O3 supported on conducting polymer (polypyrrole) as a highly potent electrocatalyst for water splitting J. Sol-Gel Sci. Technol. 2024 1 14

Santoro C. Arbizzani C. Erable B. Ieropoulos I. Microbial fuel cells: From fundamentals to applications. A review J. Power Sources 2017 356 225 244 28717261 10.1016/j.jpowsour.2017.03.109 PMC5465942

Alsultan M. Ameen A. M. Al-Keisy A. Swiegers G. F. Conducting-polymer nanocomposites as synergistic supports that accelerate electro-catalysis: PEDOT/Nano Co3O4/rGO as a photo catalyst of oxygen production from water J. Compos. Sci. 2021 5 9 245

Guo B. Ma P. X. Conducting polymers for tissue engineering Biomacromolecules 2018 19 6 1764 1782 29684268 10.1021/acs.biomac.8b00276 PMC6211800

Tomczykowa M. Plonska-Brzezinska M. E. Conducting polymers, hydrogels and their composites: Preparation, properties and bioapplications Polymers 2019 11 2 350 30960334 10.3390/polym11020350 PMC6419165

Ibanez J. G. Rincón M. E. Gutierrez-Granados S. Chahma M. Jaramillo-Quintero O. A. Frontana-Uribe B. A. Conducting polymers in the fields of energy, environmental remediation, and chemical–chiral sensors Chem. Rev. 2018 118 9 4731 4816 29630346 10.1021/acs.chemrev.7b00482

Maity N. Dawn A. Conducting polymer grafting: Recent and key developments Polymers 2020 12 3 709 32210062 10.3390/polym12030709 PMC7182814

Kenry L. B. Recent advances in biodegradable conducting polymers and their biomedical applications Biomacromolecules 2018 19 6 1783 1803 29787260 10.1021/acs.biomac.8b00275

Eftekhari A. Li L. Yang Y. Polyaniline supercapacitors J. Power Sources 2017 347 86 107

Beygisangchin M. Abdul Rashid S. Shafie S. Sadrolhosseini A. R. Lim H. N. Preparations, properties, and applications of polyaniline and polyaniline thin films—A review Polymers 2021 13 12 2003 34207392 10.3390/polym13122003 PMC8234317

Xie Y. Fabrication and electrochemical properties of flow-through polypyrrole and polypyrrole/polypyrrole nanoarrays Chem. Pap. 2021 75 5 1831 1840

Yussuf A. Al-Saleh M. Al-Enezi S. Abraham G. Synthesis and characterization of conductive polypyrrole: the influence of the oxidants and monomer on the electrical, thermal, and morphological properties Int. J. Polym. Sci. 2018 2018 1 4191747

Nurazzi N. M. H. M. Demon S. Z. N. Halim N. A. Mohamad I. S. Bahruji H. Abdullah N. Research Progress on Polythiophene and Its Application as Chemical Sensor Zulfaqar. J. Def. Sci. Eng. Technol. 2022 5 1 48 68

Naskar P. Maiti A. Chakraborty P. Kundu D. Biswas B. Banerjee A. Chemical supercapacitors: a review focusing on metallic compounds and conducting polymers J. Mater. Chem. A 2021 9 4 1970 2017

Zhang L. Du W. Nautiyal A. Liu Z. Zhang X. Recent progress on nanostructured conducting polymers and composites: synthesis, application and future aspects Sci. China Mater. 2018 61 3 303 352

Tajik S. Beitollahi H. Nejad F. G. Shoaie I. S. Khalilzadeh M. A. Asl M. S. et al. , Recent developments in conducting polymers: Applications for electrochemistry RSC Adv. 2020 10 62 37834 37856 35515168 10.1039/d0ra06160c PMC9057190

Kaloni T. P. Schreckenbach G. Freund M. S. Band gap modulation in polythiophene and polypyrrole-based systems Sci. Rep. 2016 6 1 36554 27827393 10.1038/srep36554 PMC5101528

Bajpai M. Srivastava R. Dhar R. Tiwari R. Review on optical and electrical properties of conducting polymers Indian J. Eng. Mater. Sci. 2016 2016 1 5842763

AL-Refai H. H. Ganash A. A. Hussein M. A. Polythiophene and its derivatives–Based nanocomposites in electrochemical sensing: A mini review Mater. Today Commun. 2021 26 101935

Sumdani M. G. Islam M. R. Yahaya A. N. A. Safie S. I. Recent advancements in synthesis, properties, and applications of conductive polymers for electrochemical energy storage devices: A review Polym. Eng. Sci. 2022 62 2 269 303

Gueye M. N. Carella A. Faure-Vincent J. Demadrille R. Simonato J.-P. Progress in understanding structure and transport properties of PEDOT-based materials: A critical review Prog. Mater. Sci. 2020 108 100616

Ramanavicius S. Ramanavicius A. Charge transfer and biocompatibility aspects in conducting polymer-based enzymatic biosensors and biofuel cells Nanomaterials 2021 11 2 371 33540587 10.3390/nano11020371 PMC7912793

Carmona-Espíndola J. Gázquez J. L. Charge transfer excitations and constrained density functional theory Theor. Chem. Acc. 2022 141 1 10

Mester D. Kállay M. Charge-transfer excitations within density functional theory: How accurate are the most recommended approaches? J. Chem. Theory Comput. 2022 18 3 1646 1662 35200021 10.1021/acs.jctc.1c01307 PMC8908740

Da Silva A. C. Córdoba de Torresi S. I. Advances in conducting, biodegradable and biocompatible copolymers for biomedical applications Front. Mater. 2019 6 98

Wang G. Morrin A. Li M. Liu N. Luo X. Nanomaterial-doped conducting polymers for electrochemical sensors and biosensors J. Mater. Chem. B 2018 6 25 4173 4190 32254591 10.1039/c8tb00817e

Luo S. Xu Z. Zhong F. Li H. Chen L. Doping-induced charge transfer in conductive polymers Chin. Chem. Lett. 2024 35 1 109014

Iqbal S. Ahmad S. Recent development in hybrid conducting polymers: synthesis, applications and future prospects J. Ind. Eng. Chem. 2018 60 53 84

Thejas R. Naveen C. Khan M. I. Prasanna G. Reddy S. Oreijah M. et al. , A review on electrical and gas-sensing properties of reduced graphene oxide-metal oxide nanocomposites Biomass Convers. Biorefin. 2024 14 12 12625 12635

Mahmoudian M. R. Basirun W. J. Sookhakian M. Woi P. M. Zalnezhad E. Hazarkhani H. et al. , Synthesis and characterization of α-Fe2O3/polyaniline nanotube composite as electrochemical sensor for uric acid detection Adv. Powder Technol. 2019 30 2 384 392

Sun D. Luo Y. Debliquy M. Zhang C. Graphene-enhanced metal oxide gas sensors at room temperature: A review Beilstein J. Nanotechnol. 2018 9 1 2832 2844 30498655 10.3762/bjnano.9.264 PMC6244217

Chavali M. S. Nikolova M. P. Metal oxide nanoparticles and their applications in nanotechnology SN Appl. Sci. 2019 1 6 607

Meer S. Kausar A. Iqbal T. Trends in conducting polymer and hybrids of conducting polymer/carbon nanotube: a review Polym.-Plast. Technol. Eng. 2016 55 13 1416 1440

Poddar A. K. Patel S. S. Patel H. D. Synthesis, characterization and applications of conductive polymers: A brief review Polym. Adv. Technol. 2021 32 12 4616 4641

Kroon R. Mengistie D. A. Kiefer D. Hynynen J. Ryan J. D. Yu L. et al. , Thermoelectric plastics: from design to synthesis, processing and structure–property relationships Chem. Soc. Rev. 2016 45 22 6147 6164 27385496 10.1039/c6cs00149a PMC5123640

Jo A. Huet C. Naguib H. E. Template-assisted self-assembly of conductive polymer electrodes for ionic electroactive polymers Front. Bioeng. Biotechnol. 2020 8 837 32850715 10.3389/fbioe.2020.00837 PMC7412994

Chondath S. K. Menamparambath M. M. Interface-assisted synthesis: a gateway to effective nanostructure tuning of conducting polymers Nanoscale Adv. 2021 3 4 918 941 36133281 10.1039/d0na00940g PMC9419666

Shahzad N. Ajmal R. Afzal A. Non-Enzymatic Electrochemical Sensors for Accurate and Accessible Uric Acid Detection J. Electrochem. Soc. 2023 170 9 097505

Abu-Thabit N. Y. Chemical oxidative polymerization of polyaniline: A practical approach for preparation of smart conductive textiles J. Chem. Educ. 2016 93 9 1606 1611

Wang Y. Liu A. Han Y. Li T. Sensors based on conductive polymers and their composites: a review Polym. Int. 2020 69 1 7 17

Brooke R. Cottis P. Talemi P. Fabretto M. Murphy P. Evans D. Recent advances in the synthesis of conducting polymers from the vapour phase Prog. Mater. Sci. 2017 86 127 146

Rangel-Olivares F. R. Arce-Estrada E. M. Cabrera-Sierra R. Synthesis and characterization of polyaniline-based polymer nanocomposites as anti-corrosion coatings Coatings 2021 11 6 653

Saddique Z. Saeed M. Afzal A. Target-imprinted polyaniline/Nb 2 O 5 nanoparticles as electrochemical interfaces for monitoring kidney function ACS Appl. Nano Mater. 2024 7 11 13472 13480

Saddique Z. S. M. Faheem M. Bajwa S. Z. Mujahid A. Afzal A. Core–shell niobium(V) oxide@molecularly imprinted polythiophene nanoreceptors for transformative, real-time creatinine analysis Nanoscale Adv. 2024 6 14 3644 3654 38989513 10.1039/d4na00300d PMC11232539

Zhang Y. Wu L. Lei W. Xia X. Xia M. Hao Q. Electrochemical determination of 4-nitrophenol at polycarbazole/N-doped graphene modified glassy carbon electrode Electrochim. Acta 2014 146 568 576

Guo G. Sun Y. Fu Q. Ma Y. Zhou Y. Xiong Z. et al. , Sol-gel synthesis of ternary conducting polymer hydrogel for application in all-solid-state flexible supercapacitor Int. J. Hydrogen Energy 2019 44 12 6103 6115

Chen T. Liu Y. Gao Z. Gao Y. Chen H. Ye H. et al. , Template-assisted Flexible-to-rigid Transition of Peptides in Head-to-tail Self-polymerization Enables Sequence-controllable and Post-modifiable Peptide Nanofibers Angew. Chem. 2025 137 4 e202415809 10.1002/anie.202415809 39266463

Zhang Y. Tao H. Wang H. Hao J. Liu Y. Yuan Y. Sol-gel synthesis of magnesium doped TiO2 thin film and its application in dye sensitized solar cell Opt. Mater. 2025 158 116446

Poolakkandy R. R. Menamparambath M. M. Soft-template-assisted synthesis: a promising approach for the fabrication of transition metal oxides Nanoscale Adv. 2020 2 11 5015 5045 36132034 10.1039/d0na00599a PMC9417152

Moein M. M. Abdel-Rehim A. Abdel-Rehim M. Recent applications of molecularly imprinted sol-gel methodology in sample preparation Molecules 2019 24 16 2889 31395795 10.3390/molecules24162889 PMC6720762

Nemani S. K. Annavarapu R. K. Mohammadian B. Raiyan A. Heil J. Haque M. A. et al. , Surface modification of polymers: methods and applications Adv. Mater. Interfaces 2018 5 24 1801247

Mahmood W. A. K. Azarian M. H. Sol-gel synthesis of polyaniline/zirconia composite conducting materials J. Polym. Res. 2016 23 1 8

Rahman Khan M. M. Chakraborty N. Conducting polymer-based gel materials: Synthesis, morphology, thermal properties, and applications in supercapacitors Gels 2024 10 9 553 39330155 10.3390/gels10090553 PMC11431190

Roy S. Mishra S. Yogi P. Saxena S. K. Sagdeo P. R. Kumar R. Synthesis of conducting polypyrrole-titanium oxide nanocomposite: study of structural, optical and electrical properties J. Inorg. Organomet. Polym. Mater. 2017 27 257 263

Deivanayaki S. Ponnuswamy V. Mariappan R. Jayamurugan P. Synthesis and characterization of polypyrrole/TiO2 composites by chemical oxidative method Optik 2013 124 12 1089 1091

Amorim S. M. Steffen G. de S Junior J. M. Brusamarello C. Z. Romio A. P. Domenico M. D. Synthesis, characterization, and application of polypyrrole/TiO2 composites in photocatalytic processes: a review Polym. Polym. Compos. 2021 29 7 1055 1074

Ji J. Zhang X. Liu J. Peng L. Chen C. Huang Z. et al. , Assembly of polypyrrole nanotube@ MnO2 composites with an improved electrochemical capacitance Mater. Sci. Eng. B 2015 198 51 56

Song Y. Dong Y. Li W. Tan Z. Ma P. Wang G. et al. , An In Situ Oxidative Polymerization Method to Synthesize Mesoporous Polypyrrole/MnO2 Composites for Supercapacitors Molecules 2024 30 1 45 39795103 10.3390/molecules30010045 PMC11720845

Gao L. Yin C. Luo Y. Duan G. Facile synthesis of the composites of polyaniline and TiO2 nanoparticles using self-assembly method and their application in gas sensing Nanomaterials 2019 9 4 493 30935021 10.3390/nano9040493 PMC6523884

Husain A. Ahmad S. Mohammad F. Electrical conductivity and alcohol sensing studies on polythiophene/tin oxide nanocomposites J. Sci. Adv. Mater. Devices 2020 5 1 84 94

Husain A. Electrical conductivity based ammonia, methanol and acetone vapour sensing studies on newly synthesized polythiophene/molybdenum oxide nanocomposite J. Sci. Adv. Mater. Devices 2021 6 4 528 537

Bhattarai D. P. Kim B. S. NIR-triggered hyperthermal effect of polythiophene nanoparticles synthesized by surfactant-free oxidative polymerization method on colorectal carcinoma cells Cells 2020 9 9 2122 32962169 10.3390/cells9092122 PMC7564425

Aryal U. K. Chakravarthi N. Park H.-Y. Bae H. Jin S.-H. Gal Y.-S. Highly efficient polyacetylene–based polyelectrolytes as cathode interfacial layers for organic solar cell applications Org. Electron. 2018 53 265 272

Ko Y. S. Yim J.-H. Synergistic enhancement of electrical and mechanical properties of polypyrrole thin films by hybridization of SiO2 with vapor phase polymerization Polymer 2016 93 167 173

Pratiwi E. Mulyasuryani A. Sabarudin A. Modification of screen printed carbon electrode (SPCE) with polypyrrole (Ppy)-SiO2 for phenol determination Int. Res. J. Pure Appl. Chem. 2018 7 1 12 18

Mane A. Navale S. T. Pawar R. C. Lee C. Patil V. B. Microstructural, optical and electrical transport properties of WO3 nanoparticles coated polypyrrole hybrid nanocomposites Synth. Met. 2015 199 187 195

Sun J. Shu X. Tian Y. Tong Z. Bai S. Luo R. et al. , Preparation of polypyrrole@ WO3 hybrids with pn heterojunction and sensing performance to triethylamine at room temperature Sens. Actuators, B 2017 238 510 517

Tran V. V. Nu T. T. V. Jung H.-R. Chang M. Advanced photocatalysts based on conducting polymer/metal oxide composites for environmental applications Polymers 2021 13 18 3031 34577932 10.3390/polym13183031 PMC8470106

Silva M. Alves N. M. Paiva M. C. Graphene-polymer nanocomposites for biomedical applications Polym. Adv. Technol. 2018 29 2 687 700

Ghosh S. Das S. Mosquera M. E. Conducting polymer-based nanohybrids for fuel cell application Polymers 2020 12 12 2993 33333881 10.3390/polym12122993 PMC7765313

Morshed M. Wang J. Gao M. Cong C. Wang Z. Polyaniline and rare earth metal oxide composition: a distinctive design approach for supercapacitor Electrochim. Acta 2021 370 137714

Hao Z. Ruan M. Guo Z. Yan W. Wu X. Liu Z. The synergistic role of the photosensitivity effect and extended space charge region in an inorganic–organic WO 3/PANI photoanode for efficient PEC water splitting Sustain. Energy Fuels 2021 5 11 2893 2906

Marimuthu T. Mohamad S. Alias Y. Needle-like polypyrrole–NiO composite for non-enzymatic detection of glucose Synth. Met. 2015 207 35 41

Zhang Z. Wu D. Jiang L. Liang F. Rui Y. Tang B. One-step synthesis based on non-aqueous sol-gel conductive polymer-coated SnO2 nanoparticles as advanced anode materials for lithium-ion batteries J. Alloys Compd. 2022 899 163274

Yang Z. Zhang C. Zhang J. Bai W. Potentiometric glucose biosensor based on core–shell Fe3O4–enzyme–polypyrrole nanoparticles Biosens. Bioelectron. 2014 51 268 273 23974157 10.1016/j.bios.2013.07.054

Khan M. U. Reddy K. R. Snguanwongchai T. Haque E. Gomes V. G. Polymer brush synthesis on surface modified carbon nanotubes via in situ emulsion polymerization Colloid Polym. Sci. 2016 294 1599 1610

Elias L. Fenouillot F. Majesté J.-C. Alcouffe P. Cassagnau P. Immiscible polymer blends stabilized with nano-silica particles: Rheology and effective interfacial tension Polymer 2008 49 20 4378 4385

Hsissou R. D. O. Berradi M. El Bouchti M. Assouag M. Elharfi A. Development rheological and anti-corrosion property of epoxy polymer and its composite Heliyon 2019 5 11 e02789 31844721 10.1016/j.heliyon.2019.e02789 PMC6895731

Hsissou R. Dagdag O. Berradi M. El Bouchti M. Assouag M. El Bachiri A. et al. , Investigation of structure and rheological behavior of a new epoxy polymer pentaglycidyl ether pentabisphenol A of phosphorus and of its composite with natural phosphate SN Appl. Sci. 2019 1 1 9

Hsissou R. Berradi M. El Bouchti M. El Bachiri A. El Harfi A. Synthesis characterization rheological and morphological study of a new epoxy resin pentaglycidyl ether pentaphenoxy of phosphorus and their composite (PGEPPP/MDA/PN) Polym. Bull. 2019 76 4859 4878

Hsissou R. Bekhta A. Elharfi A. Synthesis and characterization of a new epoxy resin homologous of DGEBA: diglycidyl bis disulfide carbon ether of bisphenol A J. Chem. Technol. Metall. 2018 53 3 414 421

Bharath G. Alhseinat E. Madhu R. Mugo S. M. Alwasel S. Harrath A. H. Facile synthesis of Au@ α-Fe2O3@ RGO ternary nanocomposites for enhanced electrochemical sensing of caffeic acid toward biomedical applications J. Alloys Compd. 2018 750 819 827

Charan C. Shahi V. K. Cobalt ferrite (CoFe 2 O 4) nanoparticles (size:∼ 10 nm) with high surface area for selective non-enzymatic detection of uric acid with excellent sensitivity and stability RSC Adv. 2016 6 64 59457 59467

Domínguez-Aragón A. Conejo-Dávila A. S. Zaragoza-Contreras E. A. Dominguez R. B. Pretreated screen-printed carbon electrode and Cu nanoparticles for creatinine detection in artificial saliva Chemosensors 2023 11 2 102

Williams R. J. Crapnell R. D. Dempsey N. C. Peeters M. Banks C. E. Nano-molecularly imprinted polymers for serum creatinine sensing using the heat transfer method Talanta Open 2022 5 100087

Kalasin S. Sangnuang P. Khownarumit P. Tang I. M. Surareungchai W. Evidence of Cu (I) coupling with creatinine using cuprous nanoparticles encapsulated with polyacrylic acid gel-Cu (II) in facilitating the determination of advanced kidney dysfunctions ACS Biomater. Sci. Eng. 2020 6 2 1247 1258 33464870 10.1021/acsbiomaterials.9b01664

Huang J. Yuan G. Cheng D. Xie F. Xia X. Li X. et al. , Sensitive electrochemical immunosensor based on MX ene-Nafion/polyaniline (PANI) for the sensitive determination of the novel biomarker sST2 for atherosclerotic coronary heart disease by differential pulse voltammetry (DPV) Anal. Lett. 2024 57 5 727 741

Alizadeh T. Mousavi Z. Molecularly imprinted polymer specific to creatinine complex with copper (II) ions for voltammetric determination of creatinine Microchim. Acta 2022 189 10 393 10.1007/s00604-022-05470-8 36151400

Ashakirin S. N. Zaid M. H. M. Haniff M. A. S. M. Masood A. Wee M. M. R. Sensitive electrochemical detection of creatinine based on electrodeposited molecular imprinting polymer modified screen printed carbon electrode Measurement 2023 210 112502

Saeb E. Asadpour-Zeynali K. Facile synthesis of TiO2@ PANI@ Au nanocomposite as an electrochemical sensor for determination of hydrazine Microchem. J. 2021 160 105603

Hsu W.-F. Wu T.-M. Electrochemical sensor based on conductive polyaniline coated hollow tin oxide nanoparticles and nitrogen doped graphene quantum dots for sensitively detecting dopamine J. Mater. Sci.: Mater. Electron. 2019 30 8449 8456

Xu T. Jin W. Wang Z. Cheng H. Huang X. Guo X. et al. , Electrospun CuO-nanoparticles-modified polycaprolactone@ polypyrrole fibers: An application to sensing glucose in saliva Nanomaterials 2018 8 3 133 29495508 10.3390/nano8030133 PMC5869624

Aydın E. B. Highly sensitive impedimetric immunosensor for determination of interleukin 6 as a cancer biomarker by using conjugated polymer containing epoxy side groups modified disposable ITO electrode Talanta 2020 215 120909 32312453 10.1016/j.talanta.2020.120909

Dhanawade R. N. Pawar N. S. Chougule M. A. Hingangavkar G. M. Jadhav Y. M. Nimbalkar T. M. et al. , Highly sensitive and selective PAni-CeO2 nanohybrid for detection of NH3 biomarker at room temperature J. Mater. Sci.: Mater. Electron. 2023 34 9 781

Zheng K.-W. Zhang Y.-D. Zhang Y.-S. Shi Y.-P. Polyaniline-Coated Flower-Like Titanium Dioxide Magnetic Fluorescent Imprinted Nanoparticles for the Determination of Transferrin in Human Serum Anal. Lett. 2024 1 15

Majumdar S. Mahanta D. Deposition of an ultra-thin polyaniline coating on a TiO 2 surface by vapor phase polymerization for electrochemical glucose sensing and photocatalytic degradation RSC Adv. 2020 10 30 17387 17395 35515627 10.1039/d0ra01571g PMC9053401

Jiao M. Li Z. Li Y. Cui M. Luo X. Poly (3, 4-ethylenedioxythiophene) doped with engineered carbon quantum dots for enhanced amperometric detection of nitrite Microchim. Acta 2018 185 1 9 10.1007/s00604-018-2784-8 29623497

Bukkitgar S. Shetti N. Fabrication of a TiO 2 and clay nanoparticle composite electrode as a sensor Anal. Methods 2017 9 30 4387 4393

Wang G. Han R. Feng X. Li Y. Lin J. Luo X. A glassy carbon electrode modified with poly (3, 4-ethylenedioxythiophene) doped with nano-sized hydroxyapatite for amperometric determination of nitrite Microchim. Acta 2017 184 1721 1727

Hui N. Sun X. Song Z. Niu S. Luo X. Gold nanoparticles and polyethylene glycols functionalized conducting polyaniline nanowires for ultrasensitive and low fouling immunosensing of alpha-fetoprotein Biosens. Bioelectron. 2016 86 143 149 27348779 10.1016/j.bios.2016.06.028

Wang W. Cui M. Song Z. Luo X. An antifouling electrochemical immunosensor for carcinoembryonic antigen based on hyaluronic acid doped conducting polymer PEDOT RSC Adv. 2016 6 91 88411 88416

Wang Y. Li C. Wu T. Ye X. Polymerized ionic liquid functionalized graphene oxide nanosheets as a sensitive platform for bisphenol A sensing Carbon 2018 129 21 28

Li M. Wang W. Chen Z. Song Z. Luo X. Electrochemical determination of paracetamol based on Au@ graphene core-shell nanoparticles doped conducting polymer PEDOT nanocomposite Sens. Actuators, B 2018 260 778 785

Bollella P. Gorton L. Enzyme based amperometric biosensors Curr. Opin. Electrochem. 2018 10 157 173

Bilgi M. Ayranci E. Development of amperometric biosensors using screen-printed carbon electrodes modified with conducting polymer and nanomaterials for the analysis of ethanol, methanol and their mixtures J. Electroanal. Chem. 2018 823 588 592

Kajisa T. Li W. Michinobu T. Sakata T. Well-designed dopamine-imprinted polymer interface for selective and quantitative dopamine detection among catecholamines using a potentiometric biosensor Biosens. Bioelectron. 2018 117 810 817 30096735 10.1016/j.bios.2018.07.014

Jakhar S. Pundir C. Preparation, characterization and application of urease nanoparticles for construction of an improved potentiometric urea biosensor Biosens. Bioelectron. 2018 100 242 250 28926823 10.1016/j.bios.2017.09.005

Kolahchi N. Braiek M. Ebrahimipour G. Ranaei-Siadat S. O. Lagarde F. Jaffrezic-Renault N. Direct detection of phenol using a new bacterial strain-based conductometric biosensor J. Environ. Chem. Eng. 2018 6 1 478 484

Soldatkina O. Soldatkin O. Velychko T. Prilipko V. Kuibida M. Dzyadevych S. Conductometric biosensor for arginine determination in pharmaceutics Bioelectrochemistry 2018 124 40 46 30007205 10.1016/j.bioelechem.2018.07.002

Minta D. Moyseowicz A. Gryglewicz S. Gryglewicz G. A promising electrochemical platform for dopamine and uric acid detection based on a polyaniline/iron oxide-tin oxide/reduced graphene oxide ternary composite Molecules 2020 25 24 5869 33322578 10.3390/molecules25245869 PMC7763624

Singh H. P. In-situ Generation of Au Nanostructures During Enzyme Free Oxidation of Uric Acid: A New Recognition at an Old Problem Colloid Interface Sci. Commun. 2017 19 5 8

Wang J. Yang B. Zhong J. Yan B. Zhang K. Zhai C. et al. , Dopamine and uric acid electrochemical sensor based on a glassy carbon electrode modified with cubic Pd and reduced graphene oxide nanocomposite J. Colloid Interface Sci. 2017 497 172 180 28284071 10.1016/j.jcis.2017.03.011

Ponnaiah S. K. Periakaruppan P. Vellaichamy B. New electrochemical sensor based on a silver-doped iron oxide nanocomposite coupled with polyaniline and its sensing application for picomolar-level detection of uric acid in human blood and urine samples J. Phys. Chem. B 2018 122 12 3037 3046 29498856 10.1021/acs.jpcb.7b11504

Bikbov B. Purcell C. A. Levey A. S. Smith M. Abdoli A. Abebe M. et al. , Global, regional, and national burden of chronic kidney disease, 1990–2017: a systematic analysis for the Global Burden of Disease Study 2017 Lancet 2020 395 10225 709 733 32061315 10.1016/S0140-6736(20)30045-3 PMC7049905

Carney E. F. The impact of chronic kidney disease on global health Nat. Rev. Nephrol. 2020 16 5 251 252 32144399 10.1038/s41581-020-0268-7

Cockwell P. Fisher L.-A. The global burden of chronic kidney disease Lancet 2020 395 10225 662 664 32061314 10.1016/S0140-6736(19)32977-0

Singh S. K. Crispin X. Zozoulenko I. V. Oxygen reduction reaction in conducting polymer PEDOT: Density functional theory study J. Phys. Chem. C 2017 121 22 12270 12277

Bais S. Singh P. K. Al3+-Responsive Ratiometric Fluorescent Sensor for Creatinine Detection: Thioflavin-T and Sulfated-β-Cyclodextrin Synergy ACS Appl. Bio Mater. 2023 6 10 4146 4157 10.1021/acsabm.3c00349 37702182

Zaman I. L. A. Athar S. Mujahid A. Afzal A. Electrocatalytic FeFe 2 O 4 embedded, spermine-imprinted polypyrrole (Fe/MIPpy) nanozymes for cancer diagnosis and prognosis J. Mater. Chem. B 2024 12 24 5898 5906 38779948 10.1039/d4tb00190g

Lim M. H. Eres R. Vasan S. Understanding loneliness in the twenty-first century: an update on correlates, risk factors, and potential solutions Soc. Psychiatr. Psychiatr. Epidemiol. 2020 55 793 810 10.1007/s00127-020-01889-7 32524169

Salehidoost R. Mansouri A. Amini M. Aminorroaya Yamini S. Aminorroaya A. Diabetes and all-cause mortality, a 18-year follow-up study Sci. Rep. 2020 10 1 3183 32081921 10.1038/s41598-020-60142-y PMC7035261

Liu D. Cheng Y. Tang Z. Chen J. Xia Y. Xu C. et al. , Potential mechanisms of methylglyoxal-induced human embryonic kidney cells damage: Regulation of oxidative stress, DNA damage, and apoptosis Chem. Biodiversity 2022 19 2 e202100829 10.1002/cbdv.202100829 34962083

Salek-Maghsoudi A. Vakhshiteh F. Torabi R. Hassani S. Ganjali M. R. Norouzi P. et al. , Recent advances in biosensor technology in assessment of early diabetes biomarkers Biosens. Bioelectron. 2018 99 122 135 28750336 10.1016/j.bios.2017.07.047

Karaman C. Karaman O. Atar N. Yola M. L. A molecularly imprinted electrochemical biosensor based on hierarchical Ti2Nb10O29 (TNO) for glucose detection Microchim. Acta 2022 189 1 24 10.1007/s00604-021-05128-x 34894290

Libich J. Máca J. Vondrák J. Čech O. Sedlaříková M. Supercapacitors: Properties and applications J. Energy Storage 2018 17 224 227

Banerjee S. , De B. , Sinha P. , Cherusseri J. and Kar K. K. , Applications of supercapacitors , Handbook of Nanocomposite Supercapacitor Materials I: Characteristics , 2020 , pp. 341–350

Tafete G. A. Abera M. K. Thothadri G. Review on nanocellulose-based materials for supercapacitors applications J. Energy Storage 2022 48 103938

Natarajan S. Ulaganathan M. Aravindan V. Building next-generation supercapacitors with battery type Ni(OH) 2 J. Mater. Chem. A 2021 9 28 15542 15585

Chodankar N. R. Pham H. D. Nanjundan A. K. Fernando J. F. Jayaramulu K. Golberg D. et al. , True meaning of pseudocapacitors and their performance metrics: asymmetric versus hybrid supercapacitors Small 2020 16 37 2002806 10.1002/smll.202002806 32761793

Tundwal A. Kumar H. Binoj B. J. Sharma R. Kumar G. Kumari R. et al. , Developments in conducting polymer-, metal oxide-, and carbon nanotube-based composite electrode materials for supercapacitors: a review RSC Adv. 2024 14 14 9406 9439 38516158 10.1039/d3ra08312h PMC10951819

Sharma P. Kumar V. Current technology of supercapacitors: A review J. Electron. Mater. 2020 49 6 3520 3532

Zhao D. Dai M. Zhao Y. Liu H. Liu Y. Wu X. Improving electrocatalytic activities of FeCo2O4@ FeCo2S4@ PPy electrodes by surface/interface regulation Nano Energy 2020 72 104715

Muzaffar A. Ahamed M. B. Deshmukh K. Thirumalai J. A review on recent advances in hybrid supercapacitors: Design, fabrication and applications Renew. Sustain. Energy Rev. 2019 101 123 145

Wu N. Bai X. Pan D. Dong B. Wei R. Naik N. et al. , Recent advances of asymmetric supercapacitors Adv. Mater. Interfaces 2021 8 1 2001710

Yanilmaz M. Dirican M. Asiri A. M. Zhang X. Flexible polyaniline-carbon nanofiber supercapacitor electrodes J. Energy Storage 2019 24 100766

Devadas B. Imae T. Effect of carbon dots on conducting polymers for energy storage applications ACS Sustain. Chem. Eng. 2018 6 1 127 134

Yan C. L. S. E. Mo Doped Nickel Sulfide with Enhanced Electrochemical Activity for Hybrid Supercapacitors ECS Meeting Abstracts 2023 3 809

Liang Y. Zhu D. Chao S. Hu M. Li D. Zhou W. et al. , Oxygen-vacancy europium-doped MnO2 ultrathin nanosheets used as asymmetric supercapacitors J. Energy Storage 2023 60 106673

Ding H. Hussein A. M. Ahmad I. Latef R. Abbas J. K. Abd Ali A. T. et al. , Conducting polymers in industry: A comprehensive review on the characterization, synthesis and application Alex. Eng. J. 2024 88 253 267

Kazemi F. Naghib S. M. Zare Y. Rhee K. Y. Biosensing applications of polyaniline (PANI)-based nanocomposites: A review Polym. Rev. 2021 61 3 553 597

Popov A. Aukstakojyte R. Gaidukevic J. Lisyte V. Kausaite-Minkstimiene A. Barkauskas J. et al. , Reduced graphene oxide and polyaniline nanofibers nanocomposite for the development of an amperometric glucose biosensor Sensors 2021 21 3 948 33535400 10.3390/s21030948 PMC7867097

Zhang Y. Zhang J. Jiang Y. Duan Z. Liu B. Zhao Q. et al. , Ultrasensitive flexible NH3 gas sensor based on polyaniline/SrGe4O9 nanocomposite with ppt-level detection ability at room temperature Sens. Actuators, B 2020 319 128293

Xing D. Zhou P. Liu Y. Wang Z. Wang P. Zheng Z. et al. , Atomically dispersed cobalt-based species anchored on polythiophene as an efficient electrocatalyst for oxygen evolution reaction Appl. Surf. Sci. 2021 545 148943

Anisimov Y. A. Evitts R. W. Cree D. E. Wilson L. D. Polyaniline/biopolymer composite systems for humidity sensor applications: A review Polymers 2021 13 16 2722 34451261 10.3390/polym13162722 PMC8400915

Turemis M. Zappi D. Giardi M. T. Basile G. Ramanaviciene A. Kapralovs A. et al. , ZnO/polyaniline composite based photoluminescence sensor for the determination of acetic acid vapor Talanta 2020 211 120658 32070567 10.1016/j.talanta.2019.120658

Zuo C. Xiao Y. Pan X. Xiong F. Zhang W. Long J. et al. , Organic-Inorganic Superlattices of Vanadium Oxide@ Polyaniline for High-Performance Magnesium-Ion Batteries ChemSusChem 2021 14 9 2093 2099 33751834 10.1002/cssc.202100263

Alipour A. Mansour Lakouraj M. Tashakkorian H. Study of the effect of band gap and photoluminescence on biological properties of polyaniline/CdS QD nanocomposites based on natural polymer Sci. Rep. 2021 11 1 1913 33479253 10.1038/s41598-020-80038-1 PMC7820255

Mello H. J. N. P. D. Faleiros M. C. Mulato M. Electrochemically activated polyaniline based ambipolar organic electrochemical transistor Electrochem. Sci. Adv. 2022 2 6 e2100176

Goswami S. Nandy S. Fortunato E. Martins R. Polyaniline and its composites engineering: A class of multifunctional smart energy materials J. Solid State Chem. 2023 317 123679

Rayar A. Chapi S. Murugendrappa M. G. Babaladimath G. Harish K. Kakarla R. R. et al. , Organic conjugated polymers and their nanostructured composites: Synthesis methodologies and electrochemical applications Nano-Struct. Nano-Objects 2024 37 101102

Thejas P. A. Mohan R. R. V. M. Varma S. J. Progress in Conducting Polymer-Based Electrospun fibers for Supercapacitor Applications: A Review ChemistrySelect 2023 8 17 e202203564

Zhong X.-B. Wang H.-Y. Yang Z.-Z. Jin B. Jiang Q.-C. Facile synthesis of mesoporous ZnCo2O4 coated with polypyrrole as an anode material for lithium-ion batteries J. Power Sources 2015 296 298 304

Gupta A. Sardana S. Dalal J. Lather S. Maan A. S. Tripathi R. et al. , Nanostructured polyaniline/graphene/Fe2O3 composites hydrogel as a high-performance flexible supercapacitor electrode material ACS Appl. Energy Mater. 2020 3 7 6434 6446

Wang S. Huang S. Yao M. Zhang Y. Niu Z. Engineering active sites of polyaniline for AlCl2+ storage in an aluminum-ion battery Angew. Chem., Int. Ed. 2020 59 29 11800 11807 10.1002/anie.202002132 32301196

Tang P.-Y. Han L.-J. Genç A. He Y.-M. Zhang X. Zhang L. et al. , Synergistic effects in 3D honeycomb-like hematite nanoflakes/branched polypyrrole nanoleaves heterostructures as high-performance negative electrodes for asymmetric supercapacitors Nano Energy 2016 22 189 201

Yang C. Zhang L. Hu N. Yang Z. Wei H. Zhang Y. Reduced graphene oxide/polypyrrole nanotube papers for flexible all-solid-state supercapacitors with excellent rate capability and high energy density J. Power Sources 2016 302 39 45

Yin Z. Fan W. Ding Y. Li J. Guan L. Zheng Q. Shell structure control of PPy-modified CuO composite nanoleaves for lithium batteries with improved cyclic performance ACS Sustain. Chem. Eng. 2015 3 3 507 517

Zhou C. Zhang Y. Li Y. Liu J. Construction of high-capacitance 3D CoO@ polypyrrole nanowire array electrode for aqueous asymmetric supercapacitor Nano Lett. 2013 13 5 2078 2085 23570565 10.1021/nl400378j

Zhou H. Han G. Xiao Y. Chang Y. Zhai H.-J. Facile preparation of polypyrrole/graphene oxide nanocomposites with large areal capacitance using electrochemical codeposition for supercapacitors J. Power Sources 2014 263 259 267

Zykova I. Maksimuk N. Rebezov M. Kuznetsova E. Derkho M. Sereda T. et al. , Interaction between heavy metals and microorganisms during wastewater treatment by activated sludge J. Eng. Appl. Sci. 2019 14 11 2139 2145

Nejati S. Minford T. E. Smolin Y. Y. Lau K. K. Enhanced charge storage of ultrathin polythiophene films within porous nanostructures ACS Nano 2014 8 6 5413 5422 24840296 10.1021/nn500007c

Parveen N. Ansari M. O. Cho M. H. Route to high surface area, mesoporosity of polyaniline–titanium dioxide nanocomposites via one pot synthesis for energy storage applications Ind. Eng. Chem. Res. 2016 55 1 116 124

Arbizzani C. Gabrielli G. Mastragostino M. Polyaniline: A new material for supercapacitor electrodes Electrochim. Acta 2001 46 14 2183 2187

Goswami S. dos Santos A. Nandy S. Igreja R. Barquinha P. Martins R. et al. , Human-motion interactive energy harvester based on polyaniline functionalized textile fibers following metal/polymer mechano-responsive charge transfer mechanism Nano Energy 2019 60 794 801

Gao L. Xiong L. Xu D. Cai J. Huang L. Zhou J. et al. , Distinctive construction of chitin-derived hierarchically porous carbon microspheres/polyaniline for high-rate supercapacitors ACS Appl. Mater. Interfaces 2018 10 34 28918 28927 30070477 10.1021/acsami.8b05891

Bavio M. A. Acosta G. G. Kessler T. Polyaniline and polyaniline-carbon black nanostructures as electrochemical capacitor electrode materials Int. J. Hydrogen Energy 2014 39 16 8582 8589

Ferreira G. Goswami S. Nandy S. Pereira L. Martins R. Fortunato E. Touch-Interactive Flexible Sustainable Energy Harvester and Self-Powered Smart Card Adv. Funct. Mater. 2020 30 5 1908994

Prasanna B. Avadhani D. Raj V. Kumar K. Y. Raghu M. Fabrication of PANI/SnO 2 Hybrid Nanocomposites via Interfacial Polymerization for High Performance Supercapacitors Applications Surf. Eng. Appl. Electrochem. 2019 55 463 471

Tian J. Cui N. Chen P. Guo K. Chen X. High-performance wearable supercapacitors based on PANI/N-CNT@ CNT fiber with a designed hierarchical core-sheath structure J. Mater. Chem. A 2021 9 36 20635 20644

Gong C. Deng F. Tsui C.-P. Xue Z. Ye Y. S. Tang C.-Y. et al. , PANI–PEG copolymer modified LiFePO 4 as a cathode material for high-performance lithium ion batteries J. Mater. Chem. A 2014 2 45 19315 19323

Ajpi C. Leiva N. Vargas M. Lundblad A. Lindbergh G. Cabrera S. Synthesis and characterization of LiFePO4–PANI hybrid material as cathode for lithium-ion batteries Materials 2020 13 12 2834 32599842 10.3390/ma13122834 PMC7344730

Puthirath A. B. John B. Gouri C. Jayalekshmi S. Lithium doped polyaniline and its composites with LiFePO 4 and LiMn 2 O 4-prospective cathode active materials for environment friendly and flexible Li-ion battery applications RSC Adv. 2015 5 85 69220 69228

Ye Y. Wang P. Sun H. Tian Z. Liu J. Liang C. Structural and electrochemical evaluation of a TiO 2–graphene oxide based sandwich structure for lithium-ion battery anodes RSC Adv. 2015 5 56 45038 45043

Zhao C. Jia X. Shu K. Yu C. Wallace G. G. Wang C. Conducting polymer composites for unconventional solid-state supercapacitors J. Mater. Chem. A 2020 8 9 4677 4699

Krishna M. Ghosh A. Muthuraj D. Das S. Mitra S. Electrocatalytic activity of polyaniline in magnesium–sulfur batteries J. Phys. Chem. Lett. 2022 13 5 1337 1343 35108012 10.1021/acs.jpclett.1c04021

Zhang K. Xu Y. Lu Y. Zhu Y. Qian Y. Wang D. et al. , A graphene oxide-wrapped bipyramidal sulfur@ polyaniline core–shell structure as a cathode for Li–S batteries with enhanced electrochemical performance J. Mater. Chem. A 2016 4 17 6404 6410

Guo H. Liu L. Wei Q. Shu H. Yang X. Yang Z. et al. , Electrochemical characterization of polyaniline–LiV3O8 nanocomposite cathode material for lithium ion batteries Electrochim. Acta 2013 94 113 123

Song L. Tang F. Xiao Z. Cao Z. Zhu H. Li A. Enhanced electrochemical properties of polyaniline-coated LiNi 0.8 Co 0.1 Mn 0.1 O 2 cathode material for lithium-ion batteries J. Electron. Mater. 2018 47 5896 5904

Ensafi A. A. Ahmadi N. Rezaei B. Electrochemical preparation and characterization of a polypyrrole/nickel-cobalt hexacyanoferrate nanocomposite for supercapacitor applications RSC Adv. 2015 5 111 91448 91456

Barakzehi M. Montazer M. Sharif F. Norby T. Chatzitakis A. A textile-based wearable supercapacitor using reduced graphene oxide/polypyrrole composite Electrochim. Acta 2019 305 187 196

Thakur A. K. Choudhary R. B. Majumder M. Gupta G. Shelke M. V. Enhanced electrochemical performance of polypyrrole coated MoS2 nanocomposites as electrode material for supercapacitor application J. Electroanal. Chem. 2016 782 278 287

Wu X. Wang Q. Zhang W. Wang Y. Chen W. Nanorod structure of Polypyrrole-covered MoO3 for supercapacitors with excellent cycling stability Mater. Lett. 2016 182 121 124

Cai Z. Xiong H. Zhu Z. Huang H. Li L. Huang Y. et al. , Electrochemical synthesis of graphene/polypyrrole nanotube composites for multifunctional applications Synth. Met. 2017 227 100 105

Staffell I. Scamman D. Abad A. V. Balcombe P. Dodds P. E. Ekins P. et al. , The role of hydrogen and fuel cells in the global energy system Energy Environ. Sci. 2019 12 2 463 491

Saleem F. Ni B. Yong Y. Gu L. Wang X. Ultra-small Tetrametallic Pt-Pd-Rh-Ag Nanoframes with Tunable Behavior for Direct Formic Acid/Methanol Oxidation Small 2016 12 38 5261 5268 27550307 10.1002/smll.201601299

Shi Z. Chu W. Hou Y. Gao Y. Yang N. Asymmetric supercapacitors with high energy densities Nanoscale 2019 11 24 11946 11955 31188368 10.1039/c9nr02607j

Dutta K. Das S. Rana D. Kundu P. P. Enhancements of catalyst distribution and functioning upon utilization of conducting polymers as supporting matrices in DMFCs: a review Polym. Rev. 2015 55 1 1 56

Agyekum E. B. Nutakor C. Agwa A. M. Kamel S. A critical review of renewable hydrogen production methods: factors affecting their scale-up and its role in future energy generation Membranes 2022 12 2 173 35207094 10.3390/membranes12020173 PMC8880752

Bodzek M. Membrane separation techniques: removal of inorganic and organic admixtures and impurities from water environment Arch. Environ. Protect. 2019 45 4 4 19

Dou B. Zhang H. Song Y. Zhao L. Jiang B. He M. et al. , Hydrogen production from the thermochemical conversion of biomass: issues and challenges Sustain. Energy Fuels 2019 3 2 314 342

Khan M. Al-Shankiti I. Ziani A. Idriss H. Demonstration of green hydrogen production using solar energy at 28% efficiency and evaluation of its economic viability Sustain. Energy Fuels 2021 5 4 1085 1094

Moss B. Babacan O. Kafizas A. Hankin A. A review of inorganic photoelectrode developments and reactor scale-up challenges for solar hydrogen production Adv. Energy Mater. 2021 11 13 2003286

Park S.-G. Rajesh P. Sim Y.-U. Jadhav D. A. Noori M. T. Kim D.-H. et al. , Addressing scale-up challenges and enhancement in performance of hydrogen-producing microbial electrolysis cell through electrode modifications Energy Rep. 2022 8 2726 2746

Xiang H. Ch P. Nawaz M. A. Chupradit S. Fatima A. Sadiq M. Integration and economic viability of fueling the future with green hydrogen: An integration of its determinants from renewable economics Int. J. Hydrogen Energy 2021 46 77 38145 38162

Younas M. Shafique S. Hafeez A. Javed F. Rehman F. An overview of hydrogen production: current status, potential, and challenges Fuel 2022 316 123317

Mikołajczyk T. The impact of pollutants on catalyst performance during hydrogen evolution reaction: A brief review Synth. Met. 2023 296 117379

Kichigin V. Shein A. The kinetics of hydrogen evolution reaction accompanied by hydrogen absorption reaction with consideration of subsurface hydrogen as an adsorbed species: Polarization curve J. Electroanal. Chem. 2020 873 114427

Verma J. Goel S. Cost-effective electrocatalysts for hydrogen evolution reactions (HER): challenges and prospects Int. J. Hydrogen Energy 2022 47 92 38964 38982

Schumacher S. Madauß L. Liebsch Y. Tetteh E. B. Varhade S. Schuhmann W. et al. , Revealing the Heterogeneity of Large-Area MoS2 Layers in the Electrocatalytic Hydrogen Evolution Reaction Chemelectrochem 2022 9 17 e202200586 36246850 10.1002/celc.202200586 PMC9544614

Sheng Q. Du Y. Dong Y. Zhao J. Zhong X. Xie Y. The introduction of dual pyridinic N atoms into dibenzo [b, d] thiophene sulfone containing conjugated polymers for improved hydrogen evolution: Experimental and theoretical study Appl. Surf. Sci. 2022 603 154425

Çirmi D. Karatekin R. S. Aydın R. Köleli F. Hydrogen evolution and CO2-reduction on a non-supported polypyrrole electrode Synth. Met. 2022 289 117102

Xu L. Zhang Y. Feng L. Li X. Cui Y. An Q. Active basal plane catalytic activity via interfacial engineering for a finely tunable conducting polymer/MoS2 hydrogen evolution reaction multilayer structure ACS Appl. Mater. Interfaces 2021 13 1 734 744 33390014 10.1021/acsami.0c20176

Krishnan A. Shibli S. M. A. Electroactive P-Ani/core-shell/TiO2/TiO2-WO3 employed surface engineering of Ni-P electrodes for alkaline hydrogen evolution reaction J. Ind. Eng. Chem. 2020 87 198 212

Vinodh R. Deviprasath C. Gopi C. V. M. Kummara V. G. R. Atchudan R. Ahamad T. et al. , Novel 13X Zeolite/PANI electrocatalyst for hydrogen and oxygen evolution reaction Int. J. Hydrogen Energy 2020 45 53 28337 28349

Mendoza A. E. P. Andronescu C. Olean-Oliveira A. Design of Conducting Polymer/Metal-based Nanocomposites as Electrocatalysts for Electrochemical Energy Conversion Synth. Met. 2024 117662

Torres C. Moreno B. Chinarro E. de Fraga Malfatti C. Nickel-polyaniline composite electrodes for hydrogen evolution reaction in alkaline media Int. J. Hydrogen Energy 2017 42 32 20410 20419

Jayaseelan S. S. Bhuvanendran N. Xu Q. Su H. Co3O4 nanoparticles decorated Polypyrrole/carbon nanocomposite as efficient bi-functional electrocatalyst for electrochemical water splitting Int. J. Hydrogen Energy 2020 45 7 4587 4595

Abd El-Moghny M. G. Alalawy H. H. Mohammad A. M. Mazhar A. A. El-Deab M. S. El-Anadouli B. E. Conducting polymers inducing catalysis: Enhanced formic acid electro-oxidation at a Pt/polyaniline nanocatalyst Int. J. Hydrogen Energy 2017 42 16 11166 11176

Wang J. Deng Q. Wang Y. Tunable oxidation state of Co in CoOx@ N-doped graphene derived from PANI/Co3O4 and the enhanced oxygen reduction catalysis Appl. Surf. Sci. 2019 465 665 671

Cao X. Yan W. Jin C. Tian J. Ke K. Yang R. Surface modification of MnCo2O4 with conducting polypyrrole as a highly active bifunctional electrocatalyst for oxygen reduction and oxygen evolution reaction Electrochim. Acta 2015 180 788 794

Chinnappan A. Bandal H. Ramakrishna S. Kim H. Facile synthesis of polypyrrole/ionic liquid nanoparticles and use as an electrocatalyst for oxygen evolution reaction Chem. Eng. J. 2018 335 215 220

Alwadai N. Manzoor S. Ejaz S. R. Khosa R. Y. Aman S. Al-Buriahi M. et al. , CoFe2O4 surface modification with conducting polypyrrole: employed as a highly active electrocatalyst for oxygen evolution reaction J. Mater. Sci.: Mater. Electron. 2022 33 16 13244 13254

Farid S. Ren S. Tian D. Qiu W. Zhao J. Zhao L. et al. , 3D flower-like polypyrrole-derived N-doped porous carbon coupled cobalt oxide as efficient oxygen evolution electrocatalyst Int. J. Hydrogen Energy 2020 45 56 31926 31941

Mao H. Guo X. Fu Y. Cao Z. Sun D. Wang B. et al. , Efficiently improving oxygen evolution activity using hierarchical α-Co (OH) 2/polypyrrole/graphene oxide nanosheets Appl. Surf. Sci. 2019 485 554 563

Jia L. Du G. Han D. Wang Y. Zhao W. Su Q. et al. , Magnetic electrode configuration with polypyrrole-wrapped Ni/NiFe2O4 core–shell nanospheres to boost electrocatalytic water splitting Chem. Eng. J. 2023 454 140278

Xia C. Chen W. Wang X. Hedhili M. N. Wei N. Alshareef H. N. Highly stable supercapacitors with conducting polymer core-shell electrodes for energy storage applications Adv. Energy Mater. 2015 5 8 1401805

Gueskine V. Singh A. Vagin M. Crispin X. Zozoulenko I. Molecular oxygen activation at a conducting polymer: electrochemical oxygen reduction reaction at PEDOT revisited, a theoretical study J. Phys. Chem. C 2020 124 24 13263 13272

Zhou Q. Shi G. Conducting polymer-based catalysts J. Am. Chem. Soc. 2016 138 9 2868 2876 26863332 10.1021/jacs.5b12474

Chowdhury A. D. Agnihotri N. Sen P. De A. Conducting CoMn2O4-PEDOT nanocomposites as catalyst in oxygen reduction reaction Electrochim. Acta 2014 118 81 87

Zeng F. Mebrahtu C. Liao L. Beine A. K. Palkovits R. Stability and deactivation of OER electrocatalysts: A review J. Energy Chem. 2022 69 301 329

Gmucová K. Fundamental aspects of organic conductive polymers as electrodes Curr. Opin. Electrochem. 2022 36 101117

Cao L.-M. Zaman W. Q. Sun W. Yang J. Anchoring of IrO 2 on one-dimensional Co 3 O 4 nanorods for robust electrocatalytic water splitting in an acidic environment ACS Appl. Energy Mater. 2018 1 11 6374 6380

Mugheri A. Q. Samtio M. S. Sangah A. A. Awan J. H. Memon S. A. Promoting highly dispersed Co3O4 nanoparticles onto polyethyne unraveling the catalytic mechanism with stable catalytic activity for oxygen evolution reaction: From fundamentals to applications Int. J. Hydrogen Energy 2021 46 71 35261 35270

Iftikhar S. Aslam S. Duran H. Çitoğlu S. Kirchhoff K. Lieberwirth I. et al. , Poly (3-hexylthiophene) stabilized ultrafine nickel oxide nanoparticles as superior electrocatalyst for oxygen evolution reaction: Catalyst design through synergistic combination of π-conjugated polymers and metal-based nanoparticles J. Appl. Polym. Sci. 2022 139 29 e52636

Hussein J. El-Banna M. Razik T. A. El-Naggar M. E. Biocompatible zinc oxide nanocrystals stabilized via hydroxyethyl cellulose for mitigation of diabetic complications Int. J. Biol. Macromol. 2018 107 748 754 28939513 10.1016/j.ijbiomac.2017.09.056

Johar M. A. Afzal R. A. Alazba A. A. Manzoor U. Photocatalysis and bandgap engineering using ZnO nanocomposites Adv. Mater. Sci. Eng. 2015 2015 1 934587

Wang X. Zhang M. Zhao J. Huang G. Sun H. Fe3O4@ polyaniline yolk-shell micro/nanospheres as bifunctional materials for lithium storage and electromagnetic wave absorption Appl. Surf. Sci. 2018 427 1054 1063

Qin R. Hao L. Liu Y. Zhang Y. Polyaniline-ZnO hybrid nanocomposites with enhanced photocatalytic and electrochemical performance ChemistrySelect 2018 3 23 6286 6293

Saravanan R. Sacari E. Gracia F. Khan M. M. Mosquera E. Gupta V. K. Conducting PANI stimulated ZnO system for visible light photocatalytic degradation of coloured dyes J. Mol. Liq. 2016 221 1029 1033

Asgari E. Esrafili A. Jafari A. J. Kalantary R. R. Nourmoradi H. Farzadkia M. The comparison of ZnO/polyaniline nanocomposite under UV and visible radiations for decomposition of metronidazole: degradation rate, mechanism and mineralization Process Saf. Environ. Prot. 2019 128 65 76

Rajeswari A. Christy E. J. S. Pius A. New insight of hybrid membrane to degrade Congo red and Reactive yellow under sunlight J. Photochem. Photobiol., B 2018 179 7 17 29289927 10.1016/j.jphotobiol.2017.12.024

Anupama C. Kaphle A. Udayabhanu N. G. Aegle marmelos assisted facile combustion synthesis of multifunctional ZnO nanoparticles: study of their photoluminescence, photo catalytic and antimicrobial activities J. Mater. Sci.: Mater. Electron. 2018 29 4238 4249

El-Naggar M. E. Shoueir K. Recent advances in polymer/metal/metal oxide hybrid nanostructures for catalytic applications: A review J. Environ. Chem. Eng. 2020 8 5 104175

Zhang Z. Wang L. Lee C. Recent advances in artificial intelligence sensors Adv. Sens. Res. 2023 2 8 2200072

Ahmer M. F. Ullah Q. Uddin M. K. Magnetic metal oxide assisted conducting polymer nanocomposites as eco-friendly electrode materials for supercapacitor applications: a review J. Polym. Eng. 2025 45 1 1 41

Dakshayini B. Reddy K. R. Mishra A. Shetti N. P. Malode S. J. Basu S. et al. , Role of conducting polymer and metal oxide-based hybrids for applications in ampereometric sensors and biosensors Microchem. J. 2019 147 7 24

Hatada M. Wilson E. Khanwalker M. Probst D. Okuda-Shimazaki J. Sode K. Current and future prospective of biosensing molecules for point-of-care sensors for diabetes biomarker Sens. Actuators, B 2022 351 130914