World journal of clinical cases · 2024
Bone block from lateral window - correcting vertical and horizontal bone deficiency in maxilla posterior site: A case report.
Клинический случайСтатьяНазвание и аннотация: Перевод пока не подготовлен
Обработка статьи · этапы, ошибки и управление
Загрузка состояния…
Ошибки и ограничения
История · было → стало
Состояние обновляется каждые 5 секунд, пока блок открыт. Процент показывается только там, где известен объём работы. Пауза останавливает продолжение этапа; текущий запрос к источнику может завершиться.
Wang Yu-Lan, Shao Wen-Jun, Wang Min
Аннотация
BACKGROUND: Lateral window approach for sinus floor lift is commonly used for vertical bone augmentation in cases when the residual bone height is less than 5 mm. However, managing cases becomes more challenging when a maxillary sinus pseudocyst is present or when there is insufficient bone width. In this case, we utilized the bone window prepared during the lateral window sinus lift as a shell for horizontal bone augmentation. This allowed for simultaneous horizontal and vertical bone augmentation immediately after the removal of the maxillary sinus pseudocyst.
CASE SUMMARY: A 28-year-old female presented to our clinic with the chief complaint of missing upper left posterior teeth. Intraoral examination showed a horizontal deficiency of the alveolar ridge contour. The height of the alveolar bone was approximately 3.6 mm on cone beam computed tomography (CBCT). And a typical well-defined 'dome-shaped' lesion in maxillary sinus was observed on CBCT imaging. The lateral bony window was prepared using a piezo-ultrasonic device, then the bony window was fixed to the buccal side of the 26 alveolar ridge using a titanium screw with a length of 10 mm and a diameter of 1.5 mm. The space between the bony window and the alveolar ridge was filled with Bio-Oss, covered with a Bio-Gide collagen membrane, and subsequently sutured. Nine months later, the patient's bone width increased from 4.8 to 10.5 mm, and the bone height increased from 3.6 to 15.6 mm. Subsequently, a Straumann® 4.1 mm × 10 mm implant was placed. The final all-ceramic crown restoration was completed four months later, and both clinical and radiographic examinations showed that the implant was successful, and the patient was satisfied with the results.
CONCLUSION: The bone block harvested from the lateral window sinus lift can be used for simultaneous horizontal bone augmentation acting as a shell for good two-dimensional bone augmentation.
CASE SUMMARY: A 28-year-old female presented to our clinic with the chief complaint of missing upper left posterior teeth. Intraoral examination showed a horizontal deficiency of the alveolar ridge contour. The height of the alveolar bone was approximately 3.6 mm on cone beam computed tomography (CBCT). And a typical well-defined 'dome-shaped' lesion in maxillary sinus was observed on CBCT imaging. The lateral bony window was prepared using a piezo-ultrasonic device, then the bony window was fixed to the buccal side of the 26 alveolar ridge using a titanium screw with a length of 10 mm and a diameter of 1.5 mm. The space between the bony window and the alveolar ridge was filled with Bio-Oss, covered with a Bio-Gide collagen membrane, and subsequently sutured. Nine months later, the patient's bone width increased from 4.8 to 10.5 mm, and the bone height increased from 3.6 to 15.6 mm. Subsequently, a Straumann® 4.1 mm × 10 mm implant was placed. The final all-ceramic crown restoration was completed four months later, and both clinical and radiographic examinations showed that the implant was successful, and the patient was satisfied with the results.
CONCLUSION: The bone block harvested from the lateral window sinus lift can be used for simultaneous horizontal bone augmentation acting as a shell for good two-dimensional bone augmentation.