PloS one · 2021
Computational modelling of hip resurfacing arthroplasty investigating the effect of femoral version on hip biomechanics.
СтатьяНазвание и аннотация: Перевод пока не подготовлен
Обработка статьи · этапы, ошибки и управление
Загрузка состояния…
Ошибки и ограничения
История · было → стало
Состояние обновляется каждые 5 секунд, пока блок открыт. Процент показывается только там, где известен объём работы. Пауза останавливает продолжение этапа; текущий запрос к источнику может завершиться.
Bourget-Murray Jonathan, Taneja Ashish, Naserkhaki Sadegh, El-Rich Marwan, Adeeb Samer, Powell James, Johnston Kelly
Аннотация
AIM: How reduced femoral neck anteversion alters the distribution of pressure and contact area in Hip Resurfacing Arthroplasty (HRA) remains unclear. The purpose of this study was to quantitatively describe the biomechanical implication of different femoral neck version angles on HRA using a finite element analysis.
MATERIALS AND METHODS: A total of sixty models were constructed to assess the effect of different femoral neck version angles on three different functional loads: 0°of hip flexion, 45°of hip flexion, and 90° of hip flexion. Femoral version was varied between 30° of anteversion to 30° of retroversion. All models were tested with the acetabular cup in four different positions: (1) 40°/15° (inclination/version), (2) 40°/25°, (3) 50°/15°, and (4) 50°/25°. Differences in range of motion due to presence of impingement, joint contact pressure, and joint contact area with different femoral versions and acetabular cup positions were calculated.
RESULTS: Impingement was found to be most significant with the femur in 30° of retroversion, regardless of acetabular cup position. Anterior hip impingement occurred earlier during hip flexion as the femur was progressively retroverted. Impingement was reduced in all models by increasing acetabular cup inclination and anteversion, yet this consequentially led to higher contact pressures. At 90° of hip flexion, contact pressures and contact areas were inversely related and showed most notable change with 30° of femoral retroversion. In this model, the contact area migrated towards the anterior implant-bone interface along the femoral neck.
CONCLUSION: Femoral retroversion in HRA influences impingement and increases joint contact pressure most when the hip is loaded in flexion. Increasing acetabular inclination decreases the area of impingement but doing so causes a reciprocal increase in joint contact pressure. It may be advisable to study femoral neck version pre-operatively to better choose hip resurfacing arthroplasty candidates.
MATERIALS AND METHODS: A total of sixty models were constructed to assess the effect of different femoral neck version angles on three different functional loads: 0°of hip flexion, 45°of hip flexion, and 90° of hip flexion. Femoral version was varied between 30° of anteversion to 30° of retroversion. All models were tested with the acetabular cup in four different positions: (1) 40°/15° (inclination/version), (2) 40°/25°, (3) 50°/15°, and (4) 50°/25°. Differences in range of motion due to presence of impingement, joint contact pressure, and joint contact area with different femoral versions and acetabular cup positions were calculated.
RESULTS: Impingement was found to be most significant with the femur in 30° of retroversion, regardless of acetabular cup position. Anterior hip impingement occurred earlier during hip flexion as the femur was progressively retroverted. Impingement was reduced in all models by increasing acetabular cup inclination and anteversion, yet this consequentially led to higher contact pressures. At 90° of hip flexion, contact pressures and contact areas were inversely related and showed most notable change with 30° of femoral retroversion. In this model, the contact area migrated towards the anterior implant-bone interface along the femoral neck.
CONCLUSION: Femoral retroversion in HRA influences impingement and increases joint contact pressure most when the hip is loaded in flexion. Increasing acetabular inclination decreases the area of impingement but doing so causes a reciprocal increase in joint contact pressure. It may be advisable to study femoral neck version pre-operatively to better choose hip resurfacing arthroplasty candidates.