American journal of dentistry · 2025
Influence of aging on mechanical and microbiological properties in CAD-CAM-milled and 3D-printed denture base resins.
СтатьяНазвание и аннотация: Перевод пока не подготовлен
Обработка статьи · этапы, ошибки и управление
Загрузка состояния…
Ошибки и ограничения
История · было → стало
Состояние обновляется каждые 5 секунд, пока блок открыт. Процент показывается только там, где известен объём работы. Пауза останавливает продолжение этапа; текущий запрос к источнику может завершиться.
Bento Victor A A, Sayeg João M C, Rosa Cleber D D R D, Lemos Cleidiel A D A, Marques Maria C S, Pellizzer Eduardo P
Аннотация
PURPOSE: To evaluate the adhesion of Candida albicans and the mechanical properties of resins in denture bases fabricated using conventional, milled, and 3D printing methods at different aging times.
METHODS: A total of 96 resin samples were manufactured, divided into three resin groups (n=32) (conventional thermally activated, milled and 3D printed), and subdivided into four aging times by thermocycling at temperatures 5± 1°C and 55 ± 1°C in 24 hours, 5,000, 10,000, 20,000 cycles (n= 8), evaluating the adhesion of C. albicans (ATCC90028), surface microhardness (Knoop), flexural strength and elastic modulus by three-point mechanical test. Data were evaluated by two-way ANOVA and Tukey's test for multiple comparisons (P< 0.05).
RESULTS: The milled resin demonstrated significantly lower colonization of C. albicans at times T0 (0.50± 1.37) (P= 0.007) and T1 (0.60±1.33) (P= 0.032) compared to other resins. The 3D-printed resin exhibited significantly lower values of surface microhardness at T1 (11.05± 0.26), T2 (10.92±0.63), and T3 (10.21± 0.45) (P< 0.001). The conventional and 3D-printed resins did not show significant differences in flexural strength over time (P> 0.05). The 3D-printed resin exhibited a significant difference in elastic modulus compared to the other resins, notably displaying the lowest value at time T3 (750.36± 29.32 MPa) (P< 0.05).
CLINICAL SIGNIFICANCE: Denture base materials compatible with the CAD-CAM system are increasingly available, leading to a rise in the use of dentures fabricated with this technology. This study provided promising evidence for CAD-CAM system denture base materials.
METHODS: A total of 96 resin samples were manufactured, divided into three resin groups (n=32) (conventional thermally activated, milled and 3D printed), and subdivided into four aging times by thermocycling at temperatures 5± 1°C and 55 ± 1°C in 24 hours, 5,000, 10,000, 20,000 cycles (n= 8), evaluating the adhesion of C. albicans (ATCC90028), surface microhardness (Knoop), flexural strength and elastic modulus by three-point mechanical test. Data were evaluated by two-way ANOVA and Tukey's test for multiple comparisons (P< 0.05).
RESULTS: The milled resin demonstrated significantly lower colonization of C. albicans at times T0 (0.50± 1.37) (P= 0.007) and T1 (0.60±1.33) (P= 0.032) compared to other resins. The 3D-printed resin exhibited significantly lower values of surface microhardness at T1 (11.05± 0.26), T2 (10.92±0.63), and T3 (10.21± 0.45) (P< 0.001). The conventional and 3D-printed resins did not show significant differences in flexural strength over time (P> 0.05). The 3D-printed resin exhibited a significant difference in elastic modulus compared to the other resins, notably displaying the lowest value at time T3 (750.36± 29.32 MPa) (P< 0.05).
CLINICAL SIGNIFICANCE: Denture base materials compatible with the CAD-CAM system are increasingly available, leading to a rise in the use of dentures fabricated with this technology. This study provided promising evidence for CAD-CAM system denture base materials.