Journal of prosthodontics : official journal of the American College of Prosthodontists · 2025
In vitro effect of simulated brushing on color stability, surface roughness, and microbial adhesion of characterizing resin composites for 3D-printed denture bases.
СтатьяНазвание и аннотация: Перевод пока не подготовлен
Обработка статьи · этапы, ошибки и управление
Загрузка состояния…
Ошибки и ограничения
История · было → стало
Состояние обновляется каждые 5 секунд, пока блок открыт. Процент показывается только там, где известен объём работы. Пауза останавливает продолжение этапа; текущий запрос к источнику может завершиться.
Bezerra Pamela Tayná Matias, de Sousa Lucas Cavalcante, Pereira Ana Larisse Carneiro, Bezerra Ana Luísa Cassiano Alves, de Souza Borges Grisi Maria Heloisa, de Fátima Dantas de Almeida Leopoldina, Batista André Ulisses Dantas, de Melo Monteiro Gabriela Queiroz, da Fonte Porto Carreiro Adriana
Аннотация
PURPOSE: This in vitro study evaluated the effect of simulated brushing on color stability, surface roughness, and microbial adhesion of resin composites with different viscosities applied to denture base materials.
MATERIALS AND METHODS: Disc-shaped specimens (10 × 3.0 mm) were fabricated using a 3D-printed denture base resin and heat-polymerized resin. Three extrinsic characterizations (2 mm thick) were applied to the 3D-printed resin specimens: one regular-viscosity (RV) and two low-viscosity (LV49, LV30), and light-cured. The heat-polymerized resin group (STG) was fabricated and characterized using a compression-molding technique. Color coordinates and color stability (ΔE00) were measured using a colorimeter; surface roughness (Ra) was assessed using an optical profilometer; and microbial adhesion (Candida albicans, log CFU/mL) was evaluated before and after 20,000 brushing cycles. Color and roughness data were analyzed using the Kruskal-Wallis test and the Wilcoxon signed-rank test, while microbial adhesion was analyzed using one-way ANOVA followed by Tukey's post hoc test (α = 0.05).
RESULTS: STG and LV49 exhibited greater color changes than did LV30 (p < 0.05), but all groups remained within clinically acceptable limits (ΔE00 ≤ 2.25). Brushing increased surface roughness in all groups except STG (p < 0.05). Microbial adhesion increased after simulated brushing (p < 0.05); however, no significant differences were observed between the groups (p > 0.05).
CONCLUSIONS: Simulated brushing affected color stability, with some groups exhibiting clinically noticeable changes. It increased surface roughness in characterizing resin composites and enhanced Candida albicans adhesion in all groups, with no significant differences between materials.
MATERIALS AND METHODS: Disc-shaped specimens (10 × 3.0 mm) were fabricated using a 3D-printed denture base resin and heat-polymerized resin. Three extrinsic characterizations (2 mm thick) were applied to the 3D-printed resin specimens: one regular-viscosity (RV) and two low-viscosity (LV49, LV30), and light-cured. The heat-polymerized resin group (STG) was fabricated and characterized using a compression-molding technique. Color coordinates and color stability (ΔE00) were measured using a colorimeter; surface roughness (Ra) was assessed using an optical profilometer; and microbial adhesion (Candida albicans, log CFU/mL) was evaluated before and after 20,000 brushing cycles. Color and roughness data were analyzed using the Kruskal-Wallis test and the Wilcoxon signed-rank test, while microbial adhesion was analyzed using one-way ANOVA followed by Tukey's post hoc test (α = 0.05).
RESULTS: STG and LV49 exhibited greater color changes than did LV30 (p < 0.05), but all groups remained within clinically acceptable limits (ΔE00 ≤ 2.25). Brushing increased surface roughness in all groups except STG (p < 0.05). Microbial adhesion increased after simulated brushing (p < 0.05); however, no significant differences were observed between the groups (p > 0.05).
CONCLUSIONS: Simulated brushing affected color stability, with some groups exhibiting clinically noticeable changes. It increased surface roughness in characterizing resin composites and enhanced Candida albicans adhesion in all groups, with no significant differences between materials.