The Laryngoscope · 2024
Multidisciplinary Advanced Surgical Planning for Slide Tracheoplasty Using 3D-Printed Models.
СтатьяПоддержка NIH: внешняя программаПоддержка исследования: вне правительства СШАНазвание и аннотация: Перевод пока не подготовлен
Обработка статьи · этапы, ошибки и управление
Загрузка состояния…
Ошибки и ограничения
История · было → стало
Состояние обновляется каждые 5 секунд, пока блок открыт. Процент показывается только там, где известен объём работы. Пауза останавливает продолжение этапа; текущий запрос к источнику может завершиться.
Richardson Clare M, Walton Scott, Park Jason S, Bonilla-Velez Juliana, Bly Randall A, Dahl John P, Parikh Sanjay R, Friedman Seth, Johnson Kaalan E
Аннотация
OBJECTIVE: The objective of this study was to develop and assess multidisciplinary advanced surgical planning (ASP) sessions using three dimensional (3D) printed models for cervicothoracic slide tracheoplasty (CST). We hypothesized that these sessions would improve surgeon confidence, streamline intraoperative planning, and highlight the utility of 3D modeling.
METHODS: 3D-printed patient-specific trachea models were used in pre-operative ASP sessions consisting of a multidisciplinary case discussion and hands-on slide tracheoplasty simulation. Participants completed a survey rating realism, utility, impact on the final surgical plan, and pre- and post-session confidence. Statistical analysis was performed via Wilcoxon and Kruskal-Wallis tests.
RESULTS: Forty-eight surveys were collected across nine sessions and 27 different physicians. On a 5-point Likert scale, models were rated as "very realistic", "very useful" (both median of 4, IQR 3-4 and 4-5, respectively). Overall confidence increased by 1.4 points (+/- 0.7, p < 0.0001), with the largest change seen in those with minimal prior slide tracheoplasty experience (p = 0.005). Participants felt that the sessions "strongly" impacted their surgical plan or anticipated performance (median 4, IQR 4-5), regardless of training level or experience.
CONCLUSION: 3D-printed patient-specific models were successfully implemented in ASP sessions for CST. Models were deemed very realistic and very useful by surgeons across multiple specialties and training levels. Surgical planning sessions also strongly impacted the final surgical plan and increased surgeon confidence for CST.
LEVEL OF EVIDENCE: 4 Laryngoscope, 134:3395-3401, 2024.
METHODS: 3D-printed patient-specific trachea models were used in pre-operative ASP sessions consisting of a multidisciplinary case discussion and hands-on slide tracheoplasty simulation. Participants completed a survey rating realism, utility, impact on the final surgical plan, and pre- and post-session confidence. Statistical analysis was performed via Wilcoxon and Kruskal-Wallis tests.
RESULTS: Forty-eight surveys were collected across nine sessions and 27 different physicians. On a 5-point Likert scale, models were rated as "very realistic", "very useful" (both median of 4, IQR 3-4 and 4-5, respectively). Overall confidence increased by 1.4 points (+/- 0.7, p < 0.0001), with the largest change seen in those with minimal prior slide tracheoplasty experience (p = 0.005). Participants felt that the sessions "strongly" impacted their surgical plan or anticipated performance (median 4, IQR 4-5), regardless of training level or experience.
CONCLUSION: 3D-printed patient-specific models were successfully implemented in ASP sessions for CST. Models were deemed very realistic and very useful by surgeons across multiple specialties and training levels. Surgical planning sessions also strongly impacted the final surgical plan and increased surgeon confidence for CST.
LEVEL OF EVIDENCE: 4 Laryngoscope, 134:3395-3401, 2024.