Veterinary surgery : VS · 2017
In vitro evaluation of square and surgeon's knots in large gauge suture.
Оценочное исследованиеСтатьяНазвание и аннотация: Перевод пока не подготовлен
Обработка статьи · этапы, ошибки и управление
Загрузка состояния…
Ошибки и ограничения
История · было → стало
Состояние обновляется каждые 5 секунд, пока блок открыт. Процент показывается только там, где известен объём работы. Пауза останавливает продолжение этапа; текущий запрос к источнику может завершиться.
Gillen Alex M, Munsterman Amelia S, Farag Ramsis, Coleridge Matthew O D, Hanson R Reid
Аннотация
OBJECTIVE: To investigate the strength and size of surgeon's and square knots for starting and ending continuous suture lines using large gauge suture.
STUDY DESIGN: In vitro mechanical study.
STUDY POPULATION: Knotted suture.
METHODS: Surgeon's and square knots were tested using 2 and 3 USP polyglactin 910 and 2 USP polydioxanone under linear tension on a universal testing machine. Failure mode and knot holding capacity (KHC) were recorded, and relative knot security (RKS) was calculated as a percentage of KHC. Comparisons were made between number of throws, suture size, suture type, and knot types. Knot volume and weight were assessed by a digital micrometer and balance, respectively.
RESULTS: There were no significant differences in KHC (P = .295), RKS (P = .307), volume (P = .128), or weight (P = .310) between square and surgeon's knots at the start or end of suture lines with the same number of throws and suture type. A minimum of 6 throws were required for start knots and 7 throws at end knots to prevent unraveling. Knots tied with 3 polyglactin 910 were strongest (P < .001) and 2 polyglactin 910 produced knots with higher KHC and RKS than 2 polydioxanone (P < .001).
CONCLUSION: No consistent differences were detected between knots types tied with the same suture material; however, number of throws affected KHC and RKS up to 6 throws in start or 7 throws in end knots. The configuration of square and surgeon's knots performed at the end of a continuous line alters their KHC, supporting the use of additional throws for knot security.
STUDY DESIGN: In vitro mechanical study.
STUDY POPULATION: Knotted suture.
METHODS: Surgeon's and square knots were tested using 2 and 3 USP polyglactin 910 and 2 USP polydioxanone under linear tension on a universal testing machine. Failure mode and knot holding capacity (KHC) were recorded, and relative knot security (RKS) was calculated as a percentage of KHC. Comparisons were made between number of throws, suture size, suture type, and knot types. Knot volume and weight were assessed by a digital micrometer and balance, respectively.
RESULTS: There were no significant differences in KHC (P = .295), RKS (P = .307), volume (P = .128), or weight (P = .310) between square and surgeon's knots at the start or end of suture lines with the same number of throws and suture type. A minimum of 6 throws were required for start knots and 7 throws at end knots to prevent unraveling. Knots tied with 3 polyglactin 910 were strongest (P < .001) and 2 polyglactin 910 produced knots with higher KHC and RKS than 2 polydioxanone (P < .001).
CONCLUSION: No consistent differences were detected between knots types tied with the same suture material; however, number of throws affected KHC and RKS up to 6 throws in start or 7 throws in end knots. The configuration of square and surgeon's knots performed at the end of a continuous line alters their KHC, supporting the use of additional throws for knot security.