The Journal of prosthetic dentistry · 2013
The influence of finish line curvature on the marginal gap width of ceramic copings.
СтатьяПоддержка исследования: вне правительства СШАНазвание и аннотация: Перевод пока не подготовлен
Обработка статьи · этапы, ошибки и управление
Загрузка состояния…
Ошибки и ограничения
История · было → стало
Состояние обновляется каждые 5 секунд, пока блок открыт. Процент показывается только там, где известен объём работы. Пауза останавливает продолжение этапа; текущий запрос к источнику может завершиться.
Asavapanumas Chutima, Leevailoj Chalermpol
Аннотация
STATEMENT OF PROBLEM: As a result of natural tooth anatomy or gingival recession, anterior teeth are more likely to present increased abutment finish line curvature.
PURPOSE: The purpose of this study was to investigate the influence of the curvature of the finish line on the marginal gap widths of ceramic copings.
MATERIAL AND METHODS: An ivorine maxillary central incisor was prepared for 3 different abutment finish line curvatures (1, 3, and 5 mm). Thirty-six copings were fabricated for each of these curvatures by using Cercon, IPS e.max, and Lava systems. The marginal gap width was measured by using a stereomicroscope, and the data were subsequently analyzed by means of a 2-way ANOVA and a 1-way ANOVA (α=.05).
RESULTS: A significantly higher mean marginal gap width was found for the 5-mm curvature group (Cercon, 76.59 ±23.01 µm; IPS e.max, 106.44 ±18.48 µm; Lava, 128.34 ±20.79 µm) than for both the 3-mm curvature group (Cercon, 60.18 ±9.74 µm; IPS e.max, 81.79 ±16.20 µm; Lava, 99.19 ±15.32 µm) and the 1-mm curvature group (Cercon, 38.3 ±6.85 µm; IPS e.max, 52.22 ±10.66 µm; Lava, 69.99 ±6.77 µm).
CONCLUSIONS: The greater the finish line curvature, the wider the marginal gap widths for the 3 ceramic systems.
PURPOSE: The purpose of this study was to investigate the influence of the curvature of the finish line on the marginal gap widths of ceramic copings.
MATERIAL AND METHODS: An ivorine maxillary central incisor was prepared for 3 different abutment finish line curvatures (1, 3, and 5 mm). Thirty-six copings were fabricated for each of these curvatures by using Cercon, IPS e.max, and Lava systems. The marginal gap width was measured by using a stereomicroscope, and the data were subsequently analyzed by means of a 2-way ANOVA and a 1-way ANOVA (α=.05).
RESULTS: A significantly higher mean marginal gap width was found for the 5-mm curvature group (Cercon, 76.59 ±23.01 µm; IPS e.max, 106.44 ±18.48 µm; Lava, 128.34 ±20.79 µm) than for both the 3-mm curvature group (Cercon, 60.18 ±9.74 µm; IPS e.max, 81.79 ±16.20 µm; Lava, 99.19 ±15.32 µm) and the 1-mm curvature group (Cercon, 38.3 ±6.85 µm; IPS e.max, 52.22 ±10.66 µm; Lava, 69.99 ±6.77 µm).
CONCLUSIONS: The greater the finish line curvature, the wider the marginal gap widths for the 3 ceramic systems.