Aesthetic plastic surgery · 2017
The Application of 3D Printing Technology for Simultaneous Orthognathic Surgery and Mandibular Contour Osteoplasty in the Treatment of Craniofacial Deformities.
СтатьяНазвание и аннотация: Перевод в очереди
Обработка статьи · этапы, ошибки и управление
Загрузка состояния…
Ошибки и ограничения
История · было → стало
Состояние обновляется каждые 5 секунд, пока блок открыт. Процент показывается только там, где известен объём работы. Пауза останавливает продолжение этапа; текущий запрос к источнику может завершиться.
Xiao Yanju, Sun Xiumei, Wang Lin, Zhang Yaoyao, Chen Kai, Wu Guomin
Аннотация
BACKGROUND: Because of the limitation of specific preoperative design and surgical templates, orthognathic surgery and mandibular contour osteoplasty are generally performed in two stages. Three-dimensional printing technology has improved the accuracy of the surgery and results in good surgical predictability easily. This study aims to confirm the effectiveness, feasibility and precision of simultaneous mandibular contour osteoplasty and orthognathic surgery with the assistance of 3D printing technology.
METHODS: Ten patients, who were diagnosed with mandibular hypertrophy and bimaxillary deformities, were included in the study. In addition to conventional orthognathic surgery, mandibular angle ostectomy, mandibular outer cortex grinding or mandibular border ostectomy was designed for mandibular hypertrophy. Optimal osteotomy lines and simulated surgeries were designed according the 3D printing model of the mandible. Then, surgical templates were made on the 3D printing model. No muscle excision was performed in any patient. Preoperative, predicted and postoperative measurements were taken, including the gonial angle (Ar-Go-Me) and the mandibular width (Go-Go).
RESULTS: All the patients had a reposeful postoperative recovery, with no indication of obvious infection, facial paralysis, osteonecrosis or bone displacement. The gonial angle was improved from 110.3° ± 11.1 to 121.3° ± 2.9, and the mandibular width was improved from 117.5 mm ± 6.8 to 111.9 mm ± 4.2. The discrepancies between simulation and postoperation of the left gonial angle, the right gonial angle and the mandibular width were 0.56° ± 0.22, 0.65° ± 0.3 and 0.49 mm ± 0.43, respectively.
CONCLUSIONS: The results of our study illustrated the predictability, feasibility and reliability of simultaneous mandibular contour osteoplasty and orthognathic surgery with the assistance of 3D printing technology. Our technique could achieve functional improvement and an aesthetic profile at the same time.
LEVEL OF EVIDENCE IV: This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 .
METHODS: Ten patients, who were diagnosed with mandibular hypertrophy and bimaxillary deformities, were included in the study. In addition to conventional orthognathic surgery, mandibular angle ostectomy, mandibular outer cortex grinding or mandibular border ostectomy was designed for mandibular hypertrophy. Optimal osteotomy lines and simulated surgeries were designed according the 3D printing model of the mandible. Then, surgical templates were made on the 3D printing model. No muscle excision was performed in any patient. Preoperative, predicted and postoperative measurements were taken, including the gonial angle (Ar-Go-Me) and the mandibular width (Go-Go).
RESULTS: All the patients had a reposeful postoperative recovery, with no indication of obvious infection, facial paralysis, osteonecrosis or bone displacement. The gonial angle was improved from 110.3° ± 11.1 to 121.3° ± 2.9, and the mandibular width was improved from 117.5 mm ± 6.8 to 111.9 mm ± 4.2. The discrepancies between simulation and postoperation of the left gonial angle, the right gonial angle and the mandibular width were 0.56° ± 0.22, 0.65° ± 0.3 and 0.49 mm ± 0.43, respectively.
CONCLUSIONS: The results of our study illustrated the predictability, feasibility and reliability of simultaneous mandibular contour osteoplasty and orthognathic surgery with the assistance of 3D printing technology. Our technique could achieve functional improvement and an aesthetic profile at the same time.
LEVEL OF EVIDENCE IV: This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 .