Clinical oral investigations · 2021
Effect of revascularisation and apexification procedures on biomechanical behaviour of immature maxillary central incisor teeth: a three-dimensional finite element analysis study.
СтатьяНазвание и аннотация: Перевод в очереди
Обработка статьи · этапы, ошибки и управление
Загрузка состояния…
Ошибки и ограничения
История · было → стало
Состояние обновляется каждые 5 секунд, пока блок открыт. Процент показывается только там, где известен объём работы. Пауза останавливает продолжение этапа; текущий запрос к источнику может завершиться.
Anthrayose Persis, Nawal Ruchika Roongta, Yadav Seema, Talwar Sangeeta, Yadav Sudha
Аннотация
OBJECTIVES: This study aimed to assess the effects of revascularisation and apexification procedures on biomechanical behaviour of immature teeth using 3-dimensional finite element analysis (3D FEA).
MATERIALS AND METHODS: Five 3D FEA permanent maxillary incisor models were developed from CBCT scans and available literature data: Model MT: Mature tooth, Model IT: Immature tooth (Cvek's stage 3), Model AT: Apexified tooth-mineral trioxide aggregate (MTA) apexification, Model RTB: Revascularised tooth with blood, and Model RTS: Revascularised tooth with supplementary scaffold. Using FEA, a masticatory load of 240N at 120° was simulated, and the Von Mises and maximum principal stresses within the models were evaluated. Failure index (FI) and weakening% were also calculated for each model.
RESULTS: On dentinal stress analysis, model MT (96.16MPa) and IT (158.38MPa) had lowest and highest stress values, respectively. Among the experimental groups, model RTS (131.12MPa) had lower stresses than AT (136.33MPa) and RTB (133.7MPa), with no significant difference among the three. Peak dentinal stresses in all the models were observed in the cervical third of the root and near the apical opening in model IT. The extent of high dentinal stress area in model RTB and RTS was lesser than that of AT. The FI and weakening% values were highest for model AT followed by RTB and RTS, among the experimental groups. However, all these treatments strengthened an immature tooth by more than 20%.
CONCLUSIONS: AT, RTB, and RTS treatments lowered the stress values and risk of fracture in immature teeth with no significant difference among the three groups.
CLINICAL RELEVANCE: Stress distribution evaluation following revascularisation/apexification was essential, with potential to influence clinical decision-making. MTA apexification and revascularisation with blood clot/supplementary scaffold lowered the stresses in immature teeth, with no significant difference among the three.
MATERIALS AND METHODS: Five 3D FEA permanent maxillary incisor models were developed from CBCT scans and available literature data: Model MT: Mature tooth, Model IT: Immature tooth (Cvek's stage 3), Model AT: Apexified tooth-mineral trioxide aggregate (MTA) apexification, Model RTB: Revascularised tooth with blood, and Model RTS: Revascularised tooth with supplementary scaffold. Using FEA, a masticatory load of 240N at 120° was simulated, and the Von Mises and maximum principal stresses within the models were evaluated. Failure index (FI) and weakening% were also calculated for each model.
RESULTS: On dentinal stress analysis, model MT (96.16MPa) and IT (158.38MPa) had lowest and highest stress values, respectively. Among the experimental groups, model RTS (131.12MPa) had lower stresses than AT (136.33MPa) and RTB (133.7MPa), with no significant difference among the three. Peak dentinal stresses in all the models were observed in the cervical third of the root and near the apical opening in model IT. The extent of high dentinal stress area in model RTB and RTS was lesser than that of AT. The FI and weakening% values were highest for model AT followed by RTB and RTS, among the experimental groups. However, all these treatments strengthened an immature tooth by more than 20%.
CONCLUSIONS: AT, RTB, and RTS treatments lowered the stress values and risk of fracture in immature teeth with no significant difference among the three groups.
CLINICAL RELEVANCE: Stress distribution evaluation following revascularisation/apexification was essential, with potential to influence clinical decision-making. MTA apexification and revascularisation with blood clot/supplementary scaffold lowered the stresses in immature teeth, with no significant difference among the three.